İmagepress c6010 image problem

[burak]

Hello there,


I have color alignment problem on imagepress c6010 printer.
auto-img and at-img-x throw errors. Black color does not replace.
When he changes the laser units, the error changes to the other color.
what i did:
dc-con clear
mn-con clear
intr-ex
itb-belt
itb-edge
auto-img
at-img-x
itb-gloss
none of these things helped me align the colors.

I request your valuable help.

WhatsApp Image 2021-11-12 at 21.42.48.jpg

[Hishamawada]

Re: İmagepress c6010 image problem

This c6010 is giving u a lot of troubles . I suggest u to offer the customer a C600/c650 or c8000 series. It will ease up the job for u .

Sent from my M2101K6I using Tapatalk

[burak]

Re: İmagepress c6010 image problem

Hello there,


You're right, the machine is causing me a lot of trouble, but they say it needs to be done, so I can't do anything.
I worked from morning till night today. I've done 3 colors (magenta, cyan, black), but the yellow color doesn't come back with 1 mm difference. I'm still thinking why the yellow color doesn't come back.

[fchu5959]

Re: İmagepress c6010 image problem

Hello there,


You're right, the machine is causing me a lot of trouble, but they say it needs to be done, so I can't do anything.
I worked from morning till night today. I've done 3 colors (magenta, cyan, black), but the yellow color doesn't come back with 1 mm difference. I'm still thinking why the yellow color doesn't come back.

Hello.

If you are not trained on this press,you can make it worse by doing a lot of things at the same time.
Read the service manual and see how color registration is done.It's only then that you can have a logical thinking to tackle this issue;otherwise,you will end with bad headache.

[Hishamawada]

Re: İmagepress c6010 image problem

If you please tell me everything you have done until now , in full details to be able to help u with your problem. Some small details will matter.



Sent from my M2101K6I using Tapatalk

[burak]

Re: İmagepress c6010 image problem

Hello there,


I write what has been done;


I adjusted the motors of the laser units to be 2.3 cm,
at-img-x and auto img 3 aligned the color in place.
but the yellow color stays 2mm right and is not aligned.
It says at-img-x and auto img complete, but the yellow color doesn't line up.
I did dc-con clear, it didn't work
I changed the location of the laser units, it did not improve.
I did init-itb and tried again, it didn't work.
I suspected it, I put a new belt and it didn't improve.
but I came across something while examining it,
which should be in itb unit,
FC9-6114-000 Genuine Canon ImagePress Torque limiter. This part is not in the machine, it is probably broken.
Could this part be related to this issue?

[Hishamawada]

Re: İmagepress c6010 image problem

I dont know why you have adjusted the laser motor speed.

I want u to return every value u have changed. Enter the default values for the engine . U can find them at the rear ,under the corner cover behind the hoppers. Then calibrate the machine and test.

Try cleaning the patch and registeration sensors over the itb.

Then , When performing at-img-x open the cover and check the patches on the belt . They should be clear printed.

Test PGs tests for all color on a large paper size and send show it to us.

Torque limiter will make color mismatch in the horizontal direction only.

U can try a different magenta laser unit , or swap it with another color and test. Magenta is the reference point for the registration , if it is not good all colors will be displaced.

Best of luck and update me with everything



Sent from my M2101K6I using Tapatalk

[burak]

Re: İmagepress c6010 image problem

Thank you for your help.
problem solved.

[Hishamawada]

Re: İmagepress c6010 image problem

Can u specify what was the solution?

Sent from my M2101K6I using Tapatalk

[burak]

Re: İmagepress c6010 image problem

Hello there,


The customer changed the settings of the mirrors of the laser unit and changed the angle of the mirrors in front of the range.
I fixed the problem by setting it up again.
Thanks for the help.

[Hishamawada]

Re: İmagepress c6010 image problem

My friend change the password for the service mode . Customers should go into the service mode .

They gave u so much trouble just because they thought they are smart .

Sent from my M2101K6I using Tapatalk

[burak]

Re: İmagepress c6010 image problem

you are absolutely right.
I will change the password. I struggled for 3 days because they didn't tell me what they were doing to the machine.