IRC5180 H1 1.1 Upgrade to Version 2.0

[Canon.Tech]

Re: IRC5180 H1 1.1 Upgrade to Version 2.0

Yes you could try, but it is most likely the touch screen is faulty, especially if the control panel buttons work?

[bondijunction80]

Re: IRC5180 H1 1.1 Upgrade to Version 2.0

Hi My friend, Thanks for the usefull information, I was wondering if you can help me please!

I have Canon C5180, I am unable to see the printer on network, also when I connect to my PC the pc unable to dedect the printer, I have setup my printer to the static IP address with inside the network so the setting are:


IP 192.168.1.80
S/M 255.255.255.0
GW 192.168.1.1

I can see the green light flashing on my network which is connect to switch, But I am not able to see the printer in network

do you this if i upload the software can help?

Thanks heaps

===============

BEST WAY TO UPDATE or RE-INSTALL H1 FIRMWARE is with USB

USB Flash Tool Procedure:http://downloads.canon.com/isg_public/USB_FLASH_TOOL.iso
Installing System Software From a Prepared USB 2.0 Flash Drive:
1. Print out a Configuration page.
2. Shut down the imagePASS (via the operation panel of the copier).
3. Power off the copier.
4. Be sure to leave the imagePASS-H1 connected to the copier (via the cross-over ethernet and communications
cables).
5. Attach the prepared USB 2.0 Flash Drive to a USB Type A connector on the imagePASS-H1.
6. DO NOT move the imagePASS-H1 service dip-switches to the service (download) position.
Leave the dip-switches in the normal position.

[bondijunction80]

Re: IRC5180 H1 1.1 Upgrade to Version 2.0

FK2-4435 - https://mega.co.nz/#!0k0SAJwA!JJAw2F...5H6wwRUWv2_rNs
FK2-4436 - https://mega.co.nz/#!91c1AYqS!CpRGWR...Q7K14cI3epFpgg
FK2-4437 - https://mega.co.nz/#!BtEEBTgb!MYdy0n...R_BMA54v9Fwk-M
FK2-4468 - https://mega.co.nz/#!45VE3DYa!WJJJpD...JlxFepkBmWjDAE

All four

Hi My friend, Do you have the Decryption key for the download, I am trying to download but it is asking me to enter the decryption key...Thanks Heaps

[ArhiFedot]

Re: IRC5180 H1 1.1 Upgrade to Version 2.0

At first, BShurilla, thank you very much for these useful links! Such a pleasure giving new life (firmware) to another one old tech!

I can see the green light flashing on my network which is connect to switch, But I am not able to see the printer in network

do you this if i upload the software can help?


===============

Maybe you should check your router settings. My advice is to turn DCHP on (and "auto" IP config on your printer). In printer's settings (or Configuration Page) you should find it's Ethernet MAC adress and then in DHCP Reservation List on your router you should bind to it a permanent IP adress. You can also do it in ARP List, for double insurance. Then reboot both devices and try!
P.S. I trust only Mikrotik and Cisco routerboards ;-)

Hi My friend, Do you have the Decryption key for the download, I am trying to download but it is asking me to enter the decryption key...Thanks Heaps

Make sure you're using an recently updated browser (for example, Firefox 22.0), Java and FlashPlayer (I have downloaded with no problems at all)