system error 110

[montana]

hi...i have canon ir 2270 after regular maintainance displaying system error 110 that means malfunction with laser unit..i checked the laser and connections the shutter but the error still appearing ..what is wrong ?any suggestions
thanks

[SCREWTAPE]

E110- refers to the laser motor.

You might just have to replace the laser

[montana]

hi..i ll try another laser..i think the fault with polygon motor..is that so?
thank you mr.screwtape

[teckat]

hi...i have canon ir 2270 after regular maintainance displaying system error 110 that means malfunction with laser unit..i checked the laser and connections the shutter but the error still appearing ..what is wrong ?any suggestions
thanks

what is sub code ?? also an E110 on this Series/model can be caused by many things other Laser

what maintenance were u doing before code ??

[montana]

hi mr teckat..yes the subcode was 001...i made aregular maitainance to the machine i vacumed some toner from inside the printer & i replaced the laser unit with other one but it's still the same..somebody told me it needs to reload the bootrom with latest firmware.is that so?&how i can get the latest firmware?
thank you for help my dear.

[teckat]

hi mr teckat..yes the subcode was 001...i made aregular maitainance to the machine i vacumed some toner from inside the printer & i replaced the laser unit with other one but it's still the same..somebody told me it needs to reload the bootrom with latest firmware.is that so?&how i can get the latest firmware?
thank you for help my dear.

I hope u did not vacuum out with printer plugged in wall ??
Using a Vacuum causes static charges/ hope u used a small brush attachment on hose to deflect static.

U may have a blown DC Controller / I would first check ALL the fuses on DC Controller for "Continuity"
Multi-testers - Testing Continuity With Multi-testers

/ when u check with meter,have machine unplugged from wall outlet/if u find an open Fuse- replace DC Controller

Pic below just points out fuses dis-regard arrow
iR4570.jpg

[teckat]

hi mr teckat..yes the subcode was 001...i made aregular maitainance to the machine i vacumed some toner from inside the printer & i replaced the laser unit with other one but it's still the same..somebody told me it needs to reload the bootrom with latest firmware.is that so?&how i can get the latest firmware?
thank you for help my dear.

to add on/ u may have bent leaf spring out of position on reg roller /
Seems odd to me , but an old tech pub from Canon mentions this for a possible E110 code

Reformed the leaf spring on the front side of the machine for the steel registration roller. The spring was not making contact with the roller.

ir4570contact.jpg

[montana]

yes mr teckat it was my fault when i used vacum...i will make check on the dc controller PCB&the leaf spring that you mentioned..by the way is this issue related to bootrom firmware as i've been told?
thanks very much for the informations mr teckat

[teckat]

yes mr teckat it was my fault when i used vacum...i will make check on the dc controller PCB&the leaf spring that you mentioned..by the way is this issue related to bootrom firmware as i've been told?
thanks very much for the informations mr teckat

Don't think u damaged boot rom / unless u vacuumed it ~~~~~~~~~~~~

[SCREWTAPE]

If it ends up being the DC.

Make sure that you replace with the right one.

Do not swap a 4570 Dc controller into a 2270.

This can also cause a E110.

Just in case the thought comes to mind.

Part# FM2-2767-000 ,2270 DC Controller PcB

[montana]

i haven't any dc controller to replace it yet...thank you for the part no.&for the advice mr screwtape..
good luck gentlemen.

[costd]

I would check the leaf spring that was mentioned before. We had an E110 on a 4570 that one of the guys serviced for a "squeak". Turned out he cleaned the leaf spring area and replaced the conductive grease with non-conductive. Sometimes it is the simple things.



Ok - I give up on the edit. I read my post and saw "a squeak" twice. Went to edit the error - only once in the post. Saved and is twice again.