IR7105 Saddle Finisher V2

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • copy_suhail
    Technician
    • Feb 2009
    • 88
    #1

    IR7105 Saddle Finisher V2

    I have IR7105 with a problem in its Saddle Finisher V2
    when turn on the two finisher tray moves , the tray 1 stop in the correct place but the second stop in the bottom of the finisher without any error so all paper after copying fall down in the floor.
    pls any help.
    Tags: 105, 223, bottom, copyi, copying, ect, error, finisher, finisher v2, paper, relate, respect, stop, tray, turn, usb, wrong
    • SCREWTAPE
      East Coast Imaging

      Site Contributor
      2,500+ Posts
      • Jan 2009
      • 3396
      #2
      If look at the panel where the trays go up and down. Look at the side, there are holes where the LED PCB detect the tray home position. Blown them out with a blower brush or clean them. If that don't work then replace the LED's.

      FG3-0082-000- LED PCB ASSEMBLY
      Attached Files

        Comment

        • teckat
          Field Supervisor

          Site Contributor
          10,000+ Posts
          • Jan 2010
          • 16083
          #3
          Originally posted by copy_suhail
          I have IR7105 with a problem in its Saddle Finisher V2
          when turn on the two finisher tray moves , the tray 1 stop in the correct place but the second stop in the bottom of the finisher without any error so all paper after copying fall down in the floor.
          pls any help.
          Sorry wrong info was posted
          think it's a           sensor intensity adjustment on your type of Finisher
          Last edited by teckat; 09-07-2010, 10:18 PM.
          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

            Comment

            • SCREWTAPE
              East Coast Imaging

              Site Contributor
              2,500+ Posts
              • Jan 2009
              • 3396
              #4
              I don't remember seeing those flag arms on a V1/V2.
              Thought home position was detected by the LED's

                Comment

                • teckat
                  Field Supervisor

                  Site Contributor
                  10,000+ Posts
                  • Jan 2010
                  • 16083
                  #5
                  Originally posted by SCREWTAPE
                  I don't remember seeing those flag arms on a V1/V2.
                  Thought home position was detected by the LED's

                  you're right / I deleted that mistake/ getting old & crazy
                  **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                    Comment

                    • SCREWTAPE
                      East Coast Imaging

                      Site Contributor
                      2,500+ Posts
                      • Jan 2009
                      • 3396
                      #6
                      Originally posted by teckat

                      you're right / I deleted that mistake/ getting old & crazy
                      Trust me I could relate.

                        Comment

                        • copy_suhail
                          Technician
                          • Feb 2009
                          • 88
                          #7
                          pls more explication sir

                            Comment

                            • SCREWTAPE
                              East Coast Imaging

                              Site Contributor
                              2,500+ Posts
                              • Jan 2009
                              • 3396
                              #8
                              The tray is not detecting home position.

                              Check the areas above that are circle in yellow and everything will become clearer.

                              There not much more to explain.

                                Comment

                                • copy_suhail
                                  Technician
                                  • Feb 2009
                                  • 88
                                  #9
                                  I got it...

                                  Thank u sir.

                                    Comment

                                    • SCREWTAPE
                                      East Coast Imaging

                                      Site Contributor
                                      2,500+ Posts
                                      • Jan 2009
                                      • 3396
                                      #10
                                      I know you can do it!

                                        Comment

                                        • teckat
                                          Field Supervisor

                                          Site Contributor
                                          10,000+ Posts
                                          • Jan 2010
                                          • 16083
                                          #11
                                          Originally posted by copy_suhail
                                          I got it...

                                          Thank u sir.
                                          Adjusting the Sensor Intensity/ PDF. BELOW for V1/V2

                                          iR7105_ID150E.pdf

                                          u can also update Finisher , easily with 7105 SST USB Firmware on a memory stick, it must be the 7105 SST USB FIRMWARE ONLY/ WHAT U DO IS TO RUN /SELECT A FULL UPDATE ON ENTIRE MACHINE
                                          Last edited by teckat; 09-08-2010, 05:21 AM.
                                          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                                            Comment

                                            • Canuck
                                              Tech Specialist

                                              1,000+ Posts
                                              • Nov 2007
                                              • 1713
                                              #12
                                              The leds are actually paper surface sensors. They detect the height of the paper stack in the tray. Like mentioned cleaning the transmitters and receivers will fix your problem

                                                Comment

                                                • AvisAustin
                                                  #13
                                                  free-books-online

                                                  Its very informative discussion.Good job!Thanks to all...

                                                  Free Books Online
                                                  Best Source of Online Books

                                                    Comment

                                                    • copy_suhail
                                                      Technician
                                                      • Feb 2009
                                                      • 88
                                                      #14
                                                      THANKS.... and My Respect and appreciation for all

                                                        Comment

                                                        Previous template Next
                                                        Working...