Need Help for IR105

[addoncopier]

Paper jam from tray1 and tray 3...tray 2 not function already...
when having jam...paper stop at Transfer charges...."more than half image already on paper"
single side and double side also having jam.
Sorry to trouble you..can i have pic of

check-lead blank edge
check- Transport drive/Main drive Assmby.
check- height of fuser inlet guide
check/swap out or replace HVT AC

[addoncopier]

Teckat, Now the machine is running like a horse. just when it photocopy or pc print the image or text will be more toward the right side around 6mm..So i always need to set the additional function "shift" left side 6mm...So, what is the problem cause the image or text print out toward the right side?

[teckat]

Teckat, Now the machine is running like a horse. just when it photocopy or pc print the image or text will be more toward the right side around 6mm..So i always need to set the additional function "shift" left side 6mm...So, what is the problem cause the image or text print out toward the right side?

u need to do and check your paper tray width adjustments
tray.JPG
T1.JPG
T2.JPG

[addoncopier]

Text and image still the same..toward right side...

[Canuck]

Service modeCOPIER>FUNCTION>MISC-P>CL-ADJ to set up timing of reg/brake clutch..then COPIER>ADJUST>FEED-ADJ>REGIST to adjust lead edge registration....set your shift to zero in additional functions before running these.

[addoncopier]

Canuck, I try modeCOPIER>FUNCTION>MISC-P>CL-ADJ ,but NG!....Then i on off machine, it still NG!...after try few time it become Active....but very long...Screen Just show active very long...nothing happen....By the way, 010B also happen...but i exchange the whole unit 1 with other machine, it work fine...

[teckat]

Canuck, I try modeCOPIER>FUNCTION>MISC-P>CL-ADJ ,but NG!....Then i on off machine, it still NG!...after try few time it become Active....but very long...Screen Just show active very long...nothing happen....By the way, 010B also happen...but i exchange the whole unit 1 with other machine, it work fine...

did u do the paper width adjustment for all trays

does this image issue happen from all paper feed sources ??? Cassettes & Decks & MF

[addoncopier]

Yup, i do the paper width adjustment...for all trays...It happen for all Cassettes and Decks

[teckat]

Yup, i do the paper width adjustment...for all trays...It happen for all Cassettes and Decks

now it points to the Paper Trans port area. do your homework, pull it out/ inspect & replace parts needed

there is no holding hands here- u need to Attack the issue/ it is called the process of elimination/

did u make up a check list of the things u have already inspected>cleaned>replaced ??

[Canuck]

Canuck, I try modeCOPIER>FUNCTION>MISC-P>CL-ADJ ,but NG!....Then i on off machine, it still NG!...after try few time it become Active....but very long...Screen Just show active very long...nothing happen....By the way, 010B also happen...but i exchange the whole unit 1 with other machine, it work fine...

I see you don't have documentation....to run the CL-ADJ must have LTR/A4 paper in left deck and also LTR/A4 in cassette 4(unless you have a paper deck set to LTR/A4). That is probably why it is failing(NG). It should feed 2 pieces of paper from left deck and 1 from cassette 4(or deck). This won't necessarily fix your problem,but if you are swapping transports this must be done. 01-0B is delay jam at internal delivery...this could be caused by broken tab on inside of upper fuser roll gear,worn int. delivery sensor actuator(usually around 4 million),bad transport fan,slipping on inside of transport belts,toner caked fuser inlet guide,fixing motor drive gear(4 million),poor separation at drum,....for starters. Does whole unit include fuser assembly? Also make sure that the plastic housing for the reg clutch is not broken where the clutch anchors to it...usually the reg will wander a bit with it broke. Like teckat said eliminate causes

[addoncopier]

I swap this problem fuser together with the whole unit 1 to the other machine, no delay jam (010B) happen....But the other fuser and whole unit 1 which is working well from the other machine..swap with it, problem of delay (010B) and problem of text toward 1 side ...still exists....

[teckat]

I swap this problem fuser together with the whole unit 1 to the other machine, no delay jam (010B) happen....But the other fuser and whole unit 1 which is working well from the other machine..swap with it, problem of delay (010B) and problem of text toward 1 side ...still exists....

tm.JPG

[addoncopier]

What is the standard setting...because this machine owner ask too many tech to repair..untill he fed up....

[addoncopier]

What is the standard setting? by the way, If i put back the old clutch CL5...no delay jam occur for 010B...but text toward 1 side still exists...i think i will try to replace a new CL9....let's see work or not...

[angelntx]

addoncopier,
Did you look and compare the settings to the spec sheet located IN the front door? There is a cut out with one screw on it on the door. It should have the spec sheet in it. Make sure that the settings in the Adjust section of service mode are the same and then work from there.

angel