Need Help for IR105

[addoncopier]

Yup, i check it already for the settings.....I just got a new CL9 from canon. Tomorrow i will replace it and see the results...Let's see tomorrow after replace CL9

[addoncopier]

I replaced the CL9 ( FH6-5016 ) and then COPIER>ADJUST>FEED-ADJ>REGIST adjust to -100, image back to normal... But i do 10 copies for single side, each copy not in the same position..slightly 2mm to 3mm differences.... then i replace the CL5...010B paper jam happen...I reused the old CL5 machine just work out no jam...I try many times..same new CL5 paper jam 010B...Pls advice

[teckat]

I replaced the CL9 ( FH6-5016 ) and then COPIER>ADJUST>FEED-ADJ>REGIST adjust to -100, image back to normal... But i do 10 copies for single side, each copy not in the same position..slightly 2mm to 3mm differences.... then i replace the CL5...010B paper jam happen...I reused the old CL5 machine just work out no jam...I try many times..same new CL5 paper jam 010B...Pls advice

cut the wire ties to CL5 (Pre-Registration Clutch)

010B Jam Code and increased edge
cassettes 3 & 4
set in Service Mode > Copier > Option > Cst U1-NAME to 0.

52T gear is found on the upper fusing roller>>
Check the key-way on the upper fuser roller drive gear it can become broken. This Causes the gear to slip on the upper fuser roller generating a jam code 010B. Gear part number is FS7-0007-000

Inspect the Upper Fuser Roller and Bearings for wear.

[Canuck]

I see you don't have documentation....to run the CL-ADJ must have LTR/A4 paper in left deck and also LTR/A4 in cassette 4(unless you have a paper deck set to LTR/A4). That is probably why it is failing(NG). It should feed 2 pieces of paper from left deck and 1 from cassette 4(or deck). This won't necessarily fix your problem,but if you are swapping transports this must be done. 01-0B is delay jam at internal delivery...this could be caused by broken tab on inside of upper fuser roll gear,worn int. delivery sensor actuator(usually around 4 million),bad transport fan,slipping on inside of transport belts,toner caked fuser inlet guide,fixing motor drive gear(4 million),poor separation at drum,....for starters. Does whole unit include fuser assembly? Also make sure that the plastic housing for the reg clutch is not broken where the clutch anchors to it...usually the reg will wander a bit with it broke. Like teckat said eliminate causes

Did you check all of this

[addoncopier]

I put A4 paper in Cassette 4 and then i run CL-ADJ, pass...but if used A4R paper will jam at finisher... (1126) area

Then i use the same method to test my other IR105 that working fine...A4 just pass, but A4r same paper will jam at finisher 1125 area...

So, this mean one of the clutch or something wrong in paper transport area?

[addoncopier]

cut the wire ties to CL5 (Pre-Registration Clutch)

010B Jam Code and increased edge
cassettes 3 & 4
set in Service Mode > Copier > Option > Cst U1-NAME to 0.

52T gear is found on the upper fusing roller>>
Check the key-way on the upper fuser roller drive gear it can become broken. This Causes the gear to slip on the upper fuser roller generating a jam code 010B. Gear part number is FS7-0007-000

Inspect the Upper Fuser Roller and Bearings for wear.

Teckat, fixing unit just well...Nothing happen no broken... still fine...

[Mikey]

iR105 paper jams & E594 etc. You said that the unit is old. I'm thinking of dust and worn out rollers.
Finisherisengage the finisher, bring it outside and blow the dust using a powerful blower. Inspect the mechanism. Put oil in some points that needed to be.
iR105:Now for the paper jams 0105 and 0214, replace the rollers especially the yellow ones. Those rollers are easily wornout. Check/clean the registration roller, replace if necessary. Check the pre-registration clutch, replace if necessary.
The bearing of lower fuser roller are easily wornout. Check the shafting of the lower fuser roller if it fits snugly to the bearing. Have that shafting refaced if necessary. Examine the 52T gear of the upper fuser roller, replace if necessary. Good luck.

[alibaba]

jamming problem

I just get a old IR105...But the machine cant work well..always paper jam at 0105,0214,E594...What should i start to inspect...?

hello
you can checke paper feed clutch and maylar feed rollers

[addoncopier]

0105, 0214 problem solve, just the connector problem...One of the pin not straight...the problem right now is machine can run, but image or text more toward one edge...try to adjust the setting in DC-Con for the "Feed ADJ>Regis> , i key in -100 already maximum, it does'not help much..so i replace new clutch for CL9...nothing change...I replaced new CL5 more worse, 010B paper jam occur, If i put back the old clutch CL5...machine just run like a horse...it just text and image toward one edge...So, i m going to check the whole pick-up assembly...

[addoncopier]

Teckat, regarding the image toward one side, Is it will cause by this clutch "FH6-5017"

[teckat]

Teckat, regarding the image toward one side, Is it will cause by this clutch "FH6-5017"

that clutch # FH6-5017 is CL20
it is part of the DEVELOPING DRIVE ASSEMBLY =FH6-5017-020

[Canuck]

i m not a canon tech...i just learn little bit of repairing knowledge....and i dun hv sevice manual....E594 what should i do? I replace the vertical path roller and clean all the clutch and parts...already...The machine at 1st can run..but paper jam at 0105 and 0214...now it become E594
By the way, after replace DC...image or text print out become more upper, leave 1 cm blank on bottom...what should i adjust? Hope you guys can help me..

I see in this earlier post that you replaced the DC-Con,and that is when the mis-registration started. Did you do a Dcon clear after replacing the board? This is mandatory

[addoncopier]

Before i replace the DCON, already have this problem..

[teckat]

CALL IN AN EXPERIENCED CANON TECH/

this is a procedure problem=
Observation - Inspection - Testing - Elimination - Re Test - Repair/Replace.

if not followed / u will never solve