e 350

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • roho
    Senior Tech

    500+ Posts
    • Mar 2009
    • 844
    #1

    [Error Code] e 350

    I was getting an 732 0001 constantly after adding a fiery during an install.Checked scanner connectors-reseated add memory. The scanner seems to init as well as the inner fin.
    Upon service mode finisher not seen-did an mmi clear-nadfa. cleared main controller-now getting e 350 0000 error-not listed in manual. Can anybody steer me in the right direction.

    If the main controller is blown, can it be substituted with one from an 5035?
    Thanks in advance!
    Tags: clear, controller, error, fiery, finisher, memory, rolle, roller, scan, scanner, service
    • charm5496
      Service Manager

      Site Contributor
      1,000+ Posts
      • Apr 2008
      • 2387
      #2
      been down this road already. You main controller #2 is blown. I can't tell you if the 5035 is compatible because I do not know what machine you are installing it in.....sorry
      Accidents don't just happen. They must be carelessly planned.

        Comment

        • mrfixit51
          Lead Service Technician

          1,000+ Posts
          • Oct 2008
          • 1975
          #3
          Main Controller Board 2 is common to all 4 units, while the Main Controller Board 1 is machine model specific...

          FM4-3830-000 MAIN CONTROLLER PCB ASS'Y, 1 iR-ADV C5051
          FM4-3831-000 MAIN CONTROLLER PCB ASS'Y, 1 iR-ADV C5045
          FM4-3832-000 MAIN CONTROLLER PCB ASS'Y, 1 iR-ADV C5035
          FM4-3833-000 MAIN CONTROLLER PCB ASS'Y, 1 iR-ADV C5030



          FM4-3838-000 MAIN CONTROLLER PCB ASS'Y, 2
          "Once a King, always a King, but once a Knight is enough!"

            Comment

            • teckat
              Field Supervisor

              Site Contributor
              10,000+ Posts
              • Jan 2010
              • 16083
              #4
              Originally posted by roho
              I was getting an 732 0001 constantly after adding a fiery during an install.Checked scanner connectors-reseated add memory. The scanner seems to init as well as the inner fin.
              Upon service mode finisher not seen-did an mmi clear-nadfa. cleared main controller-now getting e 350 0000 error-not listed in manual. Can anybody steer me in the right direction.

              If the main controller is blown, can it be substituted with one from an 5035?
              Thanks in advance!


              Replace Main Controller #2

              + check>



              imageRUNNER ADVANCED C5030 /5035 / 5045 / 5051


              E350 on the iRC5051 series machine.


              Try & re-seat the connector on the ECO ID PCB. This PCB is at the center right rear of the back of the copier. In the image below the board with the barcode label is the ECO ID PCB.


              location.jpg
              Last edited by teckat; 11-18-2010, 04:34 PM.
              **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                Comment

                • roho
                  Senior Tech

                  500+ Posts
                  • Mar 2009
                  • 844
                  #5
                  Thanks! I was installing an 5045. I'll reseat the ECO pcb first, progress on from there.

                    Comment

                    • roho
                      Senior Tech

                      500+ Posts
                      • Mar 2009
                      • 844
                      #6
                      Thanks to all-tried to reseat the eco pcb-was the controller

                        Comment

                        • mrfixit51
                          Lead Service Technician

                          1,000+ Posts
                          • Oct 2008
                          • 1975
                          #7
                          Glad you have it resolved...
                          "Once a King, always a King, but once a Knight is enough!"

                            Comment

                            • lilleputte
                              Trusted Tech

                              100+ Posts
                              • Jan 2013
                              • 154
                              #8
                              Re: e 350

                              Originally posted by charm5496
                              been down this road already. You main controller #2 is blown. I can't tell you if the 5035 is compatible because I do not know what machine you are installing it in.....sorry

                              Thanks this helped me a lot. I changed the main controller # 2 and then it worked great.


                              /Lilleputte

                                Comment

                                Previous template Next
                                Working...