Clc 1100

[mdaniel]

Hello




Grateful for any help that you may give

P.s. - Sory my english

Bestregards

M.Daniel

[charm5496]

compare the location of the prints of the two auto gradation prints. I would almost bet that the location of the print from the machine in question is not in the correct place and the unit can't see the patches. If that is the case replace your attraction and registration clutches and check your registration rollers to make sure they are rotating freely. You may want to clean and check your attraction assembly as well.

The only thing else I would suggest is to place about 20 sheets of white paper behind the page when you go to scan it in.

[mdaniel]

Ok thank i will do that.

Bestregards

M.Daniel

[charm5496]

let us know what you find and if you any further issues. But if the scanner is working on the sheet from the other machine then you have eliminated all kinds of issues that the optics could be having. Good luck.

[teckat]

Hello

I’m having some problem with clc1100 , the problem is in auto gradation of the machine.
When we try to do the auto gradation adjust, the machine print the sample to read but when we place the print and send the machine read it the machine simply say that don’t recognizes the print sample. I have clean the glasses and the mirrors, done the ccd adjust and the machine and the problem remain. I only get the machine to work when I placed the gradation print from other machine clc1110 and the machine make the reading with no problem at all, but I need to see where the problem is.

Grateful for any help that you may give

P.s. - Sory my english

Bestregards

M.Daniel

do u have a manual ??
Like charm5496 states = first check your registration / u need to check the stop attraction position of paper on the transfer sheet/ B SIDE- A SIDE

Adjusting the Attraction Position
(ATTRACT)
1) Select A4.
2) Select ADJUST>FEED-ADJ>ATTCHK.
3) Set ATT-CHK to '1' (2-sheet retention;
sides B and A), and press OK.
4) Select ATT-ON, and press OK.
• Paper will be picked up, attracted, and
stopped.
5) Slide out the transfer frame.
6) Place a ruler and paper against the marking (Figure 13-207) etched to the transfer drum ring (front, rear), and measure the position d of the paper in relation to the leading edge of the paper. Perform this for both sides A and B.
AB.JPGU also need to check & adjust>
Adjusting the Image Leading Edge Margin (RG-XA, RG-XB)
1) Select ADJUST>FEED-ADJ>RGSTCHK in service mode.
2) Set RGST-CHK to '1' (2-sheet retention; sides B and A), and press OK.
3) Select RGST-ON, and press OK.
• A total of two prints (one each shown in the figure) will be generated.
AB AB.JPGA.JPG

[teckat]

Also check your paper cassette trays/
check the image read start position.
Adjusting the Image Read Start Position (ADJ-XY)
1) Place the Test Sheet on the copyboard glass.
2) Select ADJUST>ADJ-XY in service mode.
3) on the ADJ-XY screen, press the Start key.
• The appropriate copying mode will automatically be selected, and a copy is made with a shift of about 50 mm as shown in the figure. Figure 13-213
xy.JPG
4) If part of the image is missing, decrease the setting of ADJ-X, ADJ-Y in service mode.
5) If part of the image is outside the image area, increase the setting of ADJ-X, ADJY.
6) Press the Start key once again, and make a check.
7) Press the Reset key.

[mdaniel]

First a thanks to everyone for helping.
I'm sorry for the delay in give you a feed back but I've been away and without any possibility to reply sooner. Your both post were right, there was a minimal diference in the actraction and the image read start position, when i do the both procedures to adjust to the correct value the autogradation was printed and readed all ok.

Thank for everyting and Sorry my english

M.Daniel

[teckat]

HatTip_2.jpg

Welcome, good luck, u need it with this model