IRC/CLC3220 - SRA3 grayed out on stack bypass

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • simon.spanswick
    Junior Member
    • Jul 2011
    • 9
    #1

    [Misc] IRC/CLC3220 - SRA3 grayed out on stack bypass

    Hi fellow Copytechers!

    I've got a problem with my CLC-3220 (hooked up to a ColorPass Z3000). Following an MMI reset that caused screen freeze (most helpfully solved by great people on this forum), the printer will no longer allow the detection of SRA3 paper via the manual stack bypass tray.

    I have looked through other postings and the service manual, and have got the machine to make the automatic adjustments for A4, A4R and A6 paper sizes but no success.

    I have also changed the ORG-LGL, ORG-LTR and ORG-LTRR settings in Copier>Option to 3, 2 and 2 respectively - which I believe tells the machine that it should be working in metric paper sizes. No success with this either (and I did power down the machine after each change to the settings).

    Trying to input the X/Y paper dimensions manually delivers a message saying that the guides are not set for that paper size.

    Any and all help gratefully received!
    Tags: 220, copier, dime, fiery, irc3220, paper, printer, reset, service manual, sra3
    • teckat
      Field Supervisor

      Site Contributor
      10,000+ Posts
      • Jan 2010
      • 16083
      #2
      Re: IRC/CLC3220 - SRA3 grayed out on stack bypass

      quick ??
      is it that the Fiery print driver will not see that size in MF TRAY or >
      when u place       SRA3 Paper in MF TRAY
      the 3220 will not DISPLAY SRA3 size on control panel ??

      BECAUSE U CLEARED MMI ,
      I believe u will need to re-register SRA3       size in COMMON SETTINGS FOR BYPASS TRAY

      Registering Irregular Size for Stack
      Bypass] appears -> press [Registering Irregular Size for Stack Bypass].



      COPIER>ADJUST>CST-ADJ>MF-A4R
      Use it to adjust the paper width basic value for the manual feed tray.
      COPIER>ADJUST>CST-ADJ>MF-A6R
      Use it to adjust the paper width basic value for the manual feed tray.
      COPIER>ADJUST>CST-ADJ>MF-A4
      Use it to adjust the paper width basic value for the manual feed tray.


      COPIER>FUNCTION<CST>
      Automatically adjusts cassette/manual feed tray.
      MF-A4R, MF-A6R, MF-A4
      Registers basic value of manual feeder’s (DADF’s) paper width.
      A4R width: 210mm, A6R width: 105mm, A4 width: 297mm
      • Once registered, the basic value can be fine-tuned by executing
      COPIER> ADJUST > CST-ADJ > MF-A4R, MF-A6R or MF-A4.
      Operation
      1) Place A4R size paper in the manual feeder, and set the size guide to the
      method A4R width.
      2) In this service mode, select “MF-A4R” to display the item in reverse.
      Press the OK key to perform automatic adjustment and register the
      value.
      3) Repeat Steps 1) and 2) to register the basic values for the A6R and A4
      sizes.
      Last edited by teckat; 08-23-2011, 06:02 PM.
      **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • teckat
          Field Supervisor

          Site Contributor
          10,000+ Posts
          • Jan 2010
          • 16083
          #3
          Re: IRC/CLC3220 - SRA3 grayed out on stack bypass

          Originally posted by simon.spanswick
          Hi fellow Copytechers!

          I've got a problem with my CLC-3220 (hooked up to a ColorPass Z3000). Following an MMI reset that caused screen freeze (most helpfully solved by great people on this forum), the printer will no longer allow the detection of SRA3 paper via the manual stack bypass tray.

          I have looked through other postings and the service manual, and have got the machine to make the automatic adjustments for A4, A4R and A6 paper sizes but no success.

          I have also changed the ORG-LGL, ORG-LTR and ORG-LTRR settings in Copier>Option to 3, 2 and 2 respectively - which I believe tells the machine that it should be working in metric paper sizes. No success with this either (and I did power down the machine after each change to the settings).

          Trying to input the X/Y paper dimensions manually delivers a message saying that the guides are not set for that paper size.

          Any and all help gratefully received!


          just to note

          turn 'OFF' the functions for the Stack Bypass settings under Common Settings, Drawer Eligibility for APS/ADS for the Copy, Mail Box, and Fax (Receive).
          4.jpg


          also in COMMON settings
          The default entry mode for numeric values is inches, but you can change it to millimeters by turning the Inch Entry mode 'Off'.
          COMMON.JPG
          Last edited by teckat; 08-23-2011, 06:04 PM.
          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

            Comment

            • simon.spanswick
              Junior Member
              • Jul 2011
              • 9
              #4
              Re: IRC/CLC3220 - SRA3 grayed out on stack bypass

              Originally posted by teckat
              quick ??
              is it that the Fiery print driver will not see that size in MF TRAY or >
              when u place               SRA3 Paper in MF TRAY
              the 3220 will not DISPLAY SRA3 size on control panel ??
              The 3220 will not display the SRA3 on the machine control panel. The SRA3 option is grayed out all the time - it's the only one that is not available - the 305x457 option is available.

              I tried the COPIER>ADJUST>CST-ADJ> system, and it changed the values. However, the SRA3 option remains grayed out!

                Comment

                Previous template Next
                Working...