IR2020 error "Change paper size"

[seaweal]

My machine after copies several paper A4, the monitor display "Change paper size". when I pull out and pust the paper tray(tray 1 and tray 2 is too), my machine run and copies several paper and the monitor display "change paper size " again. I check and clean whole my machine, stick 2 clutch on 2 paper tray, and check careful the sensors paper but that error not pass. Who's see this error please help me!! please help me. thanks very much!!

[teckat]

Re: IR2020 error "Change paper size"

My machine after copies several paper A4, the monitor display "Change paper size". when I pull out and pust the paper tray(tray 1 and tray 2 is too), my machine run and copies several paper and the monitor display "change paper size " again. I check and clean whole my machine, stick 2 clutch on 2 paper tray, and check careful the sensors paper but that error not pass. Who's see this error please help me!! please help me. thanks very much!!

adding an extra wrap to the spring for the Registration Sensor (SR209) flag should resolve the issue.


also check for a defective Size Detection Assy. { FM2-3319-000 }

[seaweal]

Re: IR2020 error "Change paper size"

thanks! I'll check the SR209, it may be of my problem.

[seaweal]

Re: IR2020 error "Change paper size"

I was check careful all sensor and SR209 but my problem not resolve. hix who;s can help me ? help me!

[teckat]

Re: IR2020 error "Change paper size"

I was check careful all sensor and SR209 but my problem not resolve. hix who;s can help me ? help me!

did u put extra wrap on spring ??????

replace the Size Detection Assy. { FM2-3319-000 }

[seaweal]

Re: IR2020 error "Change paper size"

excuse me! i don't understand { FM2-3319-000 } . I can't find it on my document(Canon IR2020 document). can u interpretation about it for me? please Where's it on the machine ? What's it look like? please help me. thanks very much! My english not good can U understand me ?

[teckat]

Re: IR2020 error "Change paper size"

excuse me! I don't understand { fm2-3319-000 } . I can't find it on my document(canon ir2020 document). Can u interpretation about it for me? Please where's it on the machine ? What's it look like? Please help me. Thanks very much! My english not good can u understand me ?

also make sure your cassette is not popping out of lock in position
The size of the paper in the cassette is detected by the DC controller PCB when the user changes the position of the cassette paper size lever. When the cassette is inserted in the iR host machine, the paper size lever pushes the paper size switches provided in the iR host machine to allow the DC controller PCB to detect presence of the cassette and the size of paper. Paper size switches are arranged as shown below. Paper sizes are determined by the combinations of the switches pushed by the paper size lever.

could be a defective button/or tray is not locked in correct & releasing out a bit -causing switches not to detect proper size
click on pic for better view

SIZE SW2.JPG

on cassette feeder assembly
see picture/ click on pictures
SIZE SW.JPGSR209.JPG

[songela]

Re: IR2020 error "Change paper size"

Let's know if the matter is solved, there are interesting suggestions yet!

[seaweal]

Re: IR2020 error "Change paper size"

thanks alot of yours enthusiasm. I's resolve my problem. its magnet has been rust at the pad. thank you very much!! thank you!!

[teckat]

Re: IR2020 error "Change paper size"

thanks alot of yours enthusiasm. I's resolve my problem. its magnet has been rust at the pad. thank you very much!! thank you!!

what magnet pad had rust ????

[Steve Baker]

Re: IR2020 error "Change paper size"

what magnet pad had rust ????

Ha ha!! like it... never heard of that one before... i would have settled for the extra spring winding! i guess they must have incredibly damp paper that produces enough moisture to make things a little rusty... nooo not buying it.. lets see a picture of this rusting magnet

[Steve Baker]

Re: IR2020 error "Change paper size"

what magnet pad had rust ????<img src="http://www.copytechnet.com/forums/images/smilies/eek.png" alt="" title="EEK!" smilieid="9" class="inlineimg" border="0">

<br><br>Ha ha!! like it... never heard of that one before... i would have settled for the extra spring winding! i guess they must have incredibly damp paper that produces enough moisture to make things a little rusty... nooo not buying it.. lets see a picture of this rusting magnet&nbsp;

[Steve Baker]

Re: IR2020 error &quot;Change paper size&quot;

<br><br>Ha ha!! like it... never heard of that one before... i would have settled for the extra spring winding! i guess they must have incredibly damp paper that produces enough moisture to make things a little rusty... nooo not buying it.. lets see a picture of this rusting magnet&nbsp;

i thought hard about that rusting magnet... i lost sleep over it and in 25 years of being in this trade i have never ever had a rusting magnet.... deeply gutted!!