irc3200 printer is warming up...stack

[Apach]

Hello,

Today when I printing PDF file (large) device is stack. After powering again on display stay: Printer is warming up. I try to clear server and restarting sustem but nothing happend. No error code just Printer is warming up. Any idea ? Tnx on help.

[charm5496]

Re: irc3200 printer is warming up...stack

check for an E004 in the history.

Problem :
The C3200 gets stuck in printer warming up and as it attempts to go to ready, it goes back to warming up. This cycle just continues constantly. Possible E004 0002 in the error history log.

Solution :
Remove the Delivery Vertical Path Unit on the left side of the machine. You will see a photo sensor PS5 Fixing Feeder Unit Open/Close Sensor sandwiched between two microsensors that actuate when closing the Fixing Feeder Unit. Clean that photo sensor as it fills up with dirt and dust. You may also experience an E004 0002 in the error history.

[charm5496]

Re: irc3200 printer is warming up...stack

More information:

Solution :
Check in service mode, * 2 & 8 *, under Copier > display > Dens. Look at the value for each individual color. The normal value would be between zero and one. If you have a color with a value around four or five you have an issue with the toner/starter concentration level for that color. By replacing that color drum unit you will temporarily resolve the issue due to the Developer Assembly being incorporated with the drum unit, which has the correct toner/starter concentration. To resolve this issue replace the Toner Cartridge Drive Assembly, FG6-8999-000, and the corresponding drum unit at the same time.

Solution :
Try to reseat all the connections and DIMMs on the Main Controller. If reseating the connections fails to resolve this issue you may have to replace the Memory PCB (FG3-2345-000). The Memory PCB is located on the rear frame behind the Drum Units.

[Apach]

Re: irc3200 printer is warming up...stack

Uhh....I forgot. I have a Fiery controler

[mramlawi]

Re: irc3200 printer is warming up...stack

got the same problem since one month and i changed the Cyan Drum ,thanks charm for the information u always have the answers

[teckat]

Re: irc3200 printer is warming up...stack

Uhh....I forgot. I have a Fiery controler

iR3200 Fuser.JPGiR3200 Fuser Switches.JPG

REMOVE bracket TO CLEAN sensor> DO NOT BLOW CANNED AIR IN THIS AREA

check the switch operation by pushing in center are/ both switches must close at the same time/
CLICK ON PICS TO ENLARGE

Copy of DoorSw_1.jpgCopy of DoorSw_2.jpgCopy of DoorSw_3.jpgCopy of DoorSw_4.jpg

FIX CONNECTOR SHOULD SIT IN CORRECT/WITH NO CRACKS/ WHEN U PUSH IN TO TEST>VIEW SWITCH CONNECTION
Copy of DoorSw_5.jpgCopy of DoorSw_6.jpgCopy of DoorSw_7.jpg

[Apach]

Re: irc3200 printer is warming up...stack

Tnx on advice.....I try this .

[Apach]

Re: irc3200 printer is warming up...stack

Morning to all,


I check all conectors and sensors. Problem is still persist. What next. I dont have a spar parts atm and I must to order. Any sugestion?
Tnx to all for trying to help me.

[Apach]

Re: irc3200 printer is warming up...stack

Device working over 1h and still dont give any error. Each 3min device like try to restarting.

[vigour]

Re: irc3200 printer is warming up...stack

Charm gave you 3 solutions did you read all of them.?
Did you check DENS and change the problem drum?

[charm5496]

Re: irc3200 printer is warming up...stack

Device working over 1h and still dont give any error. Each 3min device like try to restarting.

start with the door switches and sensor above the fuser assembly. They are inexpensive and can cause a ton of problems. While you are in there clean your connector for the fuser unit inside the machine.

did you reseat your main controller connections?
did you check your toner motors and density?

[teckat]

Re: irc3200 printer is warming up...stack

Device working over 1h and still dont give any error. Each 3min device like try to restarting.

post all the procedures you have followed from this forum------


try this~~~~~~~~~~~
remove all drums/ and re-seat them

remove that PS5 Fixing Feeder Unit Open/Close Sensor shown in picture and replace it /
don't go by how exterior looks/
it's inside the sensor that sometimes can not be cleaned from caked up toner

DID U CHECK THIS BELOW ?????
Check in service mode, * 2 & 8 *, under Copier > display > Dens.
Look at the value for each individual color.
The normal value would be between zero and one.
If you have a color with a value around four or five you have an issue with the toner/starter concentration level for that color.
Replace that color drum unit ------

HAVE you looked at this below ????
Enter into service mode, display density. One of the toner windows will display -4.75 and the others will display 0. The one at -4.75 has a bad toner add motor and needs to be replaced

DID you Try to re-seat all the connections and DIMMs on the Main Controller.
clean the ends of the memory !!!!!!!!! then re-seat
If re-seating the connections fails to resolve this issue you may have to replace the Memory PCB (FG3-2345-000). The Memory PCB is located on the rear frame behind the Drum Units.

[mramlawi]

Re: irc3200 printer is warming up...stack

Change the Drum one by one and try must work ,iam sure it happened with me

[Apach]

Re: irc3200 printer is warming up...stack

Im try all what you sugest except changing drum units. Tomorow I go and buy all 4 drum unit. I post here what happend tomorow PM. Thank you all for your help and the quick responses. Only the other drums for change. Today I see dens for black 0 and after jump on 4.

[teckat]

Re: irc3200 printer is warming up...stack

Im try all what you sugest except changing drum units. Tomorow I go and buy all 4 drum unit. I post here what happend tomorow PM. Thank you all for your help and the quick responses. Only the other drums for change. Today I see dens for black 0 and after jump on 4.

Today I see dens for black 0 and after jump on 4

what do u mean after jump on 4 ????