[Error Code] help IR5075 code E202 - 0101

[DANIELCANON]

hi, este codigo aparece esporadicamente. apago y enciendo el equipo y se corrige pero despues de un tiempo vuelve.gracias.

[zoraldinho]

Re: help IR5075 code E202 - 0101

The scanner does not return to the home position for vertical
scanning within a specific time.

http://www.copytechnet.com/forums/ca...02-0002-a.html

[teckat]

Re: help IR5075 code E202 - 0101

what tests have u tried so far ??????

check your ribbon connector on the reader controller

remove & re-seat the ROM on the Memory pcb board /Reader

[DANIELCANON]

Re: help IR5075 code E202 - 0101

gracias a ambos, les estare informando lo sucedido estos dias

[Rachid.Akli]

Re: help IR5075 code E202 - 0101

You've to notice something important in this model: The DADF is equiped with a reading CIS. A duplex document is read with a single passage. So, open the DADF from the upper side. get access to the CIS rails, clean and lubricate.

Rachid.

[DANIELCANON]

Re: help IR5075 code E202 - 0101

muchas gracias efectivamente el codigo aparece solo cuando se utiliza el alimentador de documentos ya que cuando se copia desde el vidrio no indica codigo.
hay alli dentro unas correas que me han dicho que hay que ajustarlas. puede alguien enviarme informacion sobre el alimentador de documentos. gracias

[teckat]

Re: help IR5075 code E202 - 0101

muchas gracias efectivamente el codigo aparece solo cuando se utiliza el alimentador de documentos ya que cuando se copia desde el vidrio no indica codigo.
hay alli dentro unas correas que me han dicho que hay que ajustarlas. puede alguien enviarme informacion sobre el alimentador de documentos. gracias

thank you very much indeed the code appears only when using the document feeder as when copying from the glass does not indicate code.
straps is in there they told me to be adjusted. can someone send me information on the document feeder. thanks




Remove covers following directions in Chapter 3 in the IR5075 DADF service manual to access CIS drive motor and belt. Item 13 Figure A40, in the IR5075 parts manual is the belt clamp. Loosen the two screws and apply pressure to the clamp making sure the belt teeth are seated in the clamp. Tighten the screws and test for CIS homing and white plate reading. With the DADF front cover removed you can watch the CIS move from home to reading position by powering the IR5075 off and on


E202-0101: Backside reading glass (Contact Image Sensor - CIS) Home Position Error. The home position
cannot be detected in the direction (outward) of the home position of the CIS.
1. Open the top cover of the DADF.
DF.JPG
2.Remove the input baffle.
3. Remove the turn-around baffle.
DF2.JPG
The E202-0101 is caused from the belt shown below not being adjusted properly or the M6 motor not getting proper voltage. Also check that the Glass Holder Assembly moves freely with no binding. Check the tie wraps on the connector for the M6 motor.
--------------------------------------------
Adjust belt tension/ U NEED TO LOOSEN THE SCREW ON PLATE > SCREW IS NEAR THAT SMALL PCB /U NEED A SMALL SCREWDRIVER TO FIT IN GAP>THEN PUSH GEAR TO TIGHTEN BELT> THEN TIGHTEN SCREW IN PLACE. DO NOT MAKE BELT TO TIGHT> IT WILL SKIP AND CAUSE NOISE & SAME ERROR CODE
DF3.JPG

[DANIELCANON]

Re: help IR5075 code E202 - 0101

efectivamente es esa la correa la cual en un primer momento parece que la ajuste demasiado porque la maquina indico el dicho codigo apenas la encendi, pero luego regule esa correa y ya no a marcado dicho codigo pero la copiadora esta a prueba por el cliente para ver si en los proximos dias indica dicho codigo estare informando gracias a todos.

DF3.JPG

[DANIELCANON]

[teckat]

Re: help IR5075 code E202 - 0101

sorry, i meant to say you move the motor

[Rachid.Akli]

Re: help IR5075 code E202 - 0101

Hi every body

I had this problem twice. As i said it before, the DADF CIS is mounted on rails. It's not moving easily to or from its home position, so try to clean the rails and, silghtly, lubricate them with CK-0551-020 .

[Iin]

Re: help IR5075 code E202 - 0101

I have problem same... Tanks for solution