Canon ir1610

[mramlawi]

Dear all
i have canon ir1610 an old machine and long time i didnt work on it , the problem occur on fax when i send a fax to some one it arrives but arrives too small i mean not original size is there;s any way to configure this ,i didnt try to made clear yet ,cos i wont to lose the data configuration .but i want to know what's the steps to configure

thanks alot

[mramlawi]

Re: Canon ir1610

No one face this problem befor ?

[teckat]

Re: Canon ir1610

No one face this problem befor ?

make sure the receiver has their RX Settings adjusted correctly


If the output paper in the receiving fax device > is not equal to the scanned size,
the image may either be reduced in size or divided into multiple pages.

This will be determined by the size of the original at the sender and the reduction capabilities of the receiver.


1. On the Send Tab, pull down the Scan Settings drop down menu and select Option.

2. The Scan Settings configuration window will open. Set the options you want on this screen (ex. Resolution, Document Size, Special Features such as Job Build and Different Size Originals, etc).

* Note - If faxing, be sure to select a supported resolution for faxing (normal - 200x100, fine - 200x200, superfine - 200x400, or ultrafine - 400x400).

3. Click the Store/Erase button.

4. Select a Scanning Mode item on the left by highlighting it.
The Scanning Mode items listed on the left are different groups of stored settings.

5. Hit the Register Name or Store Name button to change the name of the Scanning Mode item selected.
6. Press the Store button, verify the settings, and hit Yes to store your settings into that Scanning Mode item. Press Done.

II. To change the default Send settings:
1. Hit Additional Functions.
2. Select Communication Settings (if a fax board is attached, you need to select TX Settings under the Common Settings column).

3. Scroll to and select Edit Standard Send Settings.

4. Set the Scanning Mode (you can select the Scanning Mode item stored previously), File Format (TIFF, PDF, etc), and Divide into Pages options that you want to be the new defaults.
5. Hit OK.

6. The device must be restarted for the new default Send Settings to take effect

[mramlawi]

Re: Canon ir1610

Thank you so so so much

i ll try it ,by the way i tried everything and didnt work ,i tried to clear all didnt work .also the document is set correctly on the feeder ,because when i make a copy it copied normally,but what i noticed that when im puting the document that i want to send on the ADF on the screen shows words MIN i guess its abbreviation for reduction or minimizing the documents dunno .

any way i ll try ur steps and reply for you back


thanks again

[mramlawi]

Re: Canon ir1610

1. On the Send Tab, pull down the Scan Settings drop down menu and select Option.

2. The Scan Settings configuration window will open. Set the options you want on this screen (ex. Resolution, Document Size, Special Features such as Job Build and Different Size Originals, etc).

* Note - If faxing, be sure to select a supported resolution for faxing (normal - 200x100, fine - 200x200, superfine - 200x400, or ultrafine - 400x400).

3. Click the Store/Erase button.

4. Select a Scanning Mode item on the left by highlighting it.
The Scanning Mode items listed on the left are different groups of stored settings.

5. Hit the Register Name or Store Name button to change the name of the Scanning Mode item selected.
6. Press the Store button, verify the settings, and hit Yes to store your settings into that Scanning Mode item. Press Done.

Can you please tell me where 's this ??? Scan Tab i didnt see it on screen ?

[teckat]

Re: Canon ir1610

1. On the Send Tab, pull down the Scan Settings drop down menu and select Option.

2. The Scan Settings configuration window will open. Set the options you want on this screen (ex. Resolution, Document Size, Special Features such as Job Build and Different Size Originals, etc).

* Note - If faxing, be sure to select a supported resolution for faxing (normal - 200x100, fine - 200x200, superfine - 200x400, or ultrafine - 400x400).

3. Click the Store/Erase button.

4. Select a Scanning Mode item on the left by highlighting it.
The Scanning Mode items listed on the left are different groups of stored settings.

5. Hit the Register Name or Store Name button to change the name of the Scanning Mode item selected.
6. Press the Store button, verify the settings, and hit Yes to store your settings into that Scanning Mode item. Press Done.

Can you please tell me where 's this ??? Scan Tab i didnt see it on screen ?

Sorry, thinking of a different model/