[Electrical] Canon ir1018 weired Problem!

[sweet.persona]

Hi to all
i have 2 news canon ir1018 , when i turn On the machine they begain warming up 6 secand , but the LCD stop without any message and without lighting!

i tryed to upload the firmwares but Nothing! As shown in the following imageDSC_0041.jpg

[teckat]

Re: Canon ir1018 weired Problem!

Hi to all
i have 2 news canon ir1018 , when i turn On the machine they begain warming up 6 secand , but the LCD stop without any message and without lighting!

i tryed to upload the firmwares but Nothing! As shown in the following image[ATTACH=CONFIG]14687[/ATTACH]

Check your DDR MODULE PCB ASSEMBLY / located on IMAGE PROCESSOR PCB ASSEMBLY

remove and re-seat/ + check connectors
DDR.JPG

[sweet.persona]

Re: Canon ir1018 weired Problem!

i tryed but when i remove the DDR the lcd doe's not light too the Blue light !!

[sweet.persona]

Re: Canon ir1018 weired Problem!

when u see the pic of the lcd in the top u see Blue light! but when i remove the DDR and turn On the machine , the lcd No lighting on blue! so it is not DDR issu

[sweet.persona]

Re: Canon ir1018 weired Problem!

There are no other idea!

[DAG COPIERS & COMPUTERS]

Re: Canon ir1018 weired Problem!

Are both machines showing same symptoms? Brand new macines from their packaging? Try checking all the connectors properly as teckat suggested, probably some connectors have been dislodged due to vibrations during transportation. In worst case scenario you may refer machines back to supplier in order not to void their warranty. But first give it a trial.

[sweet.persona]

Re: Canon ir1018 weired Problem!

i checked all the connectors , i replaced new flat cable between DC and the board ,i replaced too another DDR but the problem still The problem has not changed !!

2/ when i attachment USB cable between the machine and PC to upload the system software PC does not deteced the PCB!!!!


can anyone help me!
thank u in advance

[teckat]

Re: Canon ir1018 weired Problem!

1) Turn off the main power switch of this machine, and then disconnect the cables connected to this machine.
2) Connect USB connector on the back of this machine to the PC using the USB cable
To download the SYSTEM software, use the steps given for the BOOT software.

in SST
select "iR1022" in "Model List".
Double-click the "System" folder in "Model List" to check the system software version.
Select "USB" in "Interface", and then click the "START button

Now Turn on the power switch of the host machine.
Press the following keys on the control panel to enter the service mode.
Additional Functions Key > 2 Key > 8 Key > Additional Functions Key
-Using the plus (+) or minus (-) key, select "#DOWNLOAD".
-Press the OK key on the control panel to place the host machine in the downloading wait mode ("#DOWNLOAD CONNECTED" is displayed).
-Press the OK button on the SST screen displayed on the display of the PC.
When connection is complete,Click the OK button.
Click "BootROM Download"

[DAG COPIERS & COMPUTERS]

Re: Canon ir1018 weired Problem!

What about your energy source? For two machines to behave in exactly same manner upon powering up could mean there is a common factor or denominator at play. Probably, apart from the BOOTING PROCESS, the warmup process is incomplete due to some AC mains power hiccup. TRY, checking your ac mains power output voltage if its to the required standard , remember also to check the available output current at the outlet, since correct output voltage does not necessarily mean it is delivering the correct current. OR Try to power the machines with the power cables plugged DIRECTLY into the WALL SOCKET, rather than using an EXTENSION cable.

Good luck.

[teckat]

Re: Canon ir1018 weired Problem!

Hi to all
i have 2 news canon ir1018 , when i turn On the machine they begain warming up 6 secand , but the LCD stop without any message and without lighting!

i tryed to upload the firmwares but Nothing! As shown in the following image[ATTACH=CONFIG]14687[/ATTACH]

where did u get these printers from ?
did you witness their functions before purchase ??

check all connectors on Image Processor PCB.

[sweet.persona]

Re: Canon ir1018 weired Problem!

i am tech and one from my Consumer This gave me the machines on the basis of repair , All new but have the same problem!!!! i tryed to upload the sys software Several attempts BUT WHEN I Connect USB between Machine and pc There is no correlation !!!!!!!!!!

Maybe the 2 Dc PCB All is lost (damaged!!!)

[teckat]

Re: Canon ir1018 weired Problem!

i am tech and one from my Consumer This gave me the machines on the basis of repair , All new but have the same problem!!!! i tryed to upload the sys software Several attempts BUT WHEN I Connect USB between Machine and pc There is no correlation !!!!!!!!!!

Maybe the 2 Dc PCB All is lost (damaged!!!)

New = means a machine has NEVER been installed before

basis of repair= fix it or lose it , I guess -

[sweet.persona]

Re: Canon ir1018 weired Problem!

More explain



When I switch on the machine ,LCD display lights and the black line moves to the right, arrive at the end then block and stuck and does not pass the stage ready to copy!!!

any idea!

[teckat]

Re: Canon ir1018 weired Problem!

More explain



When I switch on the machine ,LCD display lights and the black line moves to the right, arrive at the end then block and stuck and does not pass the stage ready to copy!!!

any idea!

Image Processor

[sweet.persona]

Re: Canon ir1018 weired Problem!

Then what i can do! Image Processor was damaged!