[Error Code] iRADC5030/C5035/C5045/C5051---E020 Error Codes----Revised to correct Part Numbers

[teckat]

E020-020X/ E020-0081/ E020-101X Error Codes (Revised)

SEE PDF---E020-020X, E020-0081, E020-101X Error Codes.pdf


Publication has been revised to correct Part Numbers FM4-8386-000 and FM4-8387-000

PRODUCTS AFFECTED / SERIAL NUMBERS AFFECTED:
Solid Fill D Shaft
Products Affected: Serial Numbers Affected:
imageRUNNER ADVANCE C5030 GNG00001 ~ GNG12193
imageRUNNER ADVANCE C5035 GNW00001 ~ GNW10951
imageRUNNER ADVANCE C5045 GPQ00001 ~ GPQ11431
imageRUNNER ADVANCE C5051 GQM00001 ~ GQM11888
Addition of Parallel Pin
Products Affected: Serial Numbers Affected:
imageRUNNER ADVANCE C5030 GNG00001 ~ GNG53414
imageRUNNER ADVANCE C5035 GNW00001 ~ GNW53158
imageRUNNER ADVANCE C5045 GPQ00001 ~ GPQ53113
imageRUNNER ADVANCE C5051 GQM00001 ~ GQM52858
Machine Front Plate
Products Affected: Serial Numbers Affected:
imageRUNNER ADVANCE C5030 GNG00001 ~ GNG52882
imageRUNNER ADVANCE C5035 GNW00001 ~ GNW52892
imageRUNNER ADVANCE C5045 GPQ00001 ~ GPQ53057
imageRUNNER ADVANCE C5051 GQM00001 ~ GQM52719

[Boomer7]

Re: iRADC5030/C5035/C5045/C5051---E020 Error Codes----Revised to correct Part Numbers

I have a machine thats 2 hrs away and I've been on site to clean patch sensor and reseat processing unit items. It worked for about 9 days then gave me the error again E020-0104. If the shutter drive ass,y was damaged as suggested in this tech pub would the error be showing up every 5-9 days after reboot or more consistent. Currently if you reboot the machine it will work for days then error E020-0104. I was thinking may be the blk drum then I found this thread with the tech pub. just trying to save trips because every visit I have to wait to see if it will error again days later. Any suggestions?

[teckat]

Re: iRADC5030/C5035/C5045/C5051---E020 Error Codes----Revised to correct Part Numbers

I have a machine thats 2 hrs away and I've been on site to clean patch sensor and reseat processing unit items. It worked for about 9 days then gave me the error again E020-0104. If the shutter drive ass,y was damaged as suggested in this tech pub would the error be showing up every 5-9 days after reboot or more consistent. Currently if you reboot the machine it will work for days then error E020-0104. I was thinking may be the blk drum then I found this thread with the tech pub. just trying to save trips because every visit I have to wait to see if it will error again days later. Any suggestions?

----------------------------------

Patch Shutter Linkage.
The linkage transfers the movement of SL1 to the Patch shutter. If the Patch Shutter is not opened during certain Image Stabilization Controls, an incorrect Patch Sensor reading will occur and cause the E020.



The Shutter Linkage does not have a part number.
You must order the Pattern Read Shutter Drive Assembly FM3-8902-000
See FIG. 321 of the Parts Catalog


check the shutter for cracks
also check for a broken slide pin ,that goes into SL1 for the Pattern Read Drive Assembly.





???


Replace patch sensor unit and black drum.

Part numbers as follows: Patch Sensor Unit =FM3-5944-010, GPR-30 Black Drum - 2776B004BA, GPR-31
Black Drum - 2778B004BA

Initialization of patch sensor is necessary. COPIER>OPTION>IMG-MCON>P-ALPHA>Input Patch Sensor alpha value.

[Tim C]

Re: iRADC5030/C5035/C5045/C5051---E020 Error Codes----Revised to correct Part Numbers

I have a IRC ADV 5045 that the customer installed the wrong toner btl. Close match GPR-31 vs GPR-30 now the machine wont come out of an E025-0410 error.. Any reset you know of ?