IRC adv 5051 Error

[Gerhard]

Hi All

Have a acceesory stapler finisher C1 giving me E 505-0001. I have put a new finisher controller board in with same result. I have moved the finisher to another 5051 and it gives the same problem.

The problem should be with the finisher.

Any ideas is welcome !!

[Rachid.Akli]

Re: IRC adv 5051 Error

Hi All

Have a acceesory stapler finisher C1 giving me E 505-0001. I have put a new finisher controller board in with same result. I have moved the finisher to another 5051 and it gives the same problem.

The problem should be with the finisher.

Any ideas is welcome !!

Hi to all

The EEPROM content is empty.

In service mode > Finisher > Adjust===> put back the RAM values.


Rachid.

[Gerhard]

Re: IRC adv 5051 Error

Hi to all

The EEPROM content is empty.

In service mode > Finisher > Adjust===> put back the RAM values.


Rachid.

Thanx will give it a try tomorrow

Regards

[Gerhard]

Re: IRC adv 5051 Error

Hi to allThe EEPROM content is empty.In service mode > Finisher > Adjust===> put back the RAM values.Rachid.

Thank You Problem solved !!!

[yazj]

Re: IRC adv 5051 Error

Thank You Problem solved !!!

i have same issue here can you give me advice please... i did already entering the value as advice but still same.


any help please


regards
Jason

[teckat]

Re: IRC adv 5051 Error

i have same issue here can you give me advice please... i did already entering the value as advice but still same.


any help please


regards
Jason

----------------------------------------------
do the alignment width guide position or has the staple position been adjusted

READ THIS
E505_001.pdf

[yazj]

Re: IRC adv 5051 Error

----------------------------------------------
do the alignment width guide position or has the staple position been adjusted

READ THIS
[ATTACH]22299[/ATTACH]

hi teckat,

thanks foro the usefull documentation,

what i did is i have the P-Print values of the machine. but when i try to put the value its not saving. it return to 0 value again.


please advice.

Thanks
Jason

[w0179651]

Re: IRC adv 5051 Error

Does this pdf document apply to the IR C4080? The saddle stitcher instructions have no effect, while stacker alignment does.

[teckat]

Re: IRC adv 5051 Error

Does this pdf document apply to the IR C4080? The saddle stitcher instructions have no effect, while stacker alignment does.

-----------------------------------------------magnifying-glass.jpg

the iRC4080 uses a Finisher W1/W2

E 505-0001
see pdf for your error/model

[w0179651]

Re: IRC adv 5051 Error

Are there alignment instruction for the saddle finisher (saddle staple position) for the W2? The staples are constantly an 1/8" from the fold.

[teckat]

Re: IRC adv 5051 Error

Are there alignment instruction for the saddle finisher (saddle staple position) for the W2? The staples are constantly an 1/8" from the fold.

-------------see pdf

Note:

Adjusting the Stitching Position
(adjusting center stitching)
Use the host machine user mode to perform that adjustment.(see below)

When using the Saddle Stitch mode of the optional Saddle Finisher-W2, and you notice that the folds of the paper are not exactly in the middle of the booklet,
you can make adjustments to the saddle stitch position to compensate for this error.

1- Press (Additional Functions *) ➞ [Adjustment/Cleaning] ➞ [Saddle Stitch Position Adjustment].
2- Select the paper size for which you want to adjust the saddle stitch position.

NOTE:
Some of the paper sizes displayed may not be available in certain countries.
3- Press [▼] or [▲] to adjust the saddle stitch position ➞ press [OK].

----------------------------------------------------- Added Information if needed
Saddle Stitch Staple Repositioning
You can reposition the stapler of the saddle stitcher unit after clearing a staple jam, or after replacing the staple cartridge. Saddle stitch staple repositioning works by
feeding several sheets of paper into the saddle stitcher unit and stapling them together.
CAUTION
If transparencies are loaded in a paper drawer, make sure to pull out that paper drawer slightly so that transparencies are not fed for the saddle stitch staple
repositioning procedure. Damage to the machine may occur if transparencies are fed during this procedure.
IMPORTANT
• Only use 12" x 18", 11" x 17", LGL, or LTRR paper for the saddle stitch staple repositioning procedure.
• Make sure to remove all output booklets from the optional Booklet Tray before performing the saddle stitch staple repositioning procedure.
NOTE
• Saddle stitch staple repositioning can be performed only if the optional Saddle Finisher-W2 is attached.
• Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine.
1- Press (Additional Functions *) ➞ [Adjustment/Cleaning] ➞ [Saddle Stitcher Staple Repositioning].
2- Press [Start].

[w0179651]

Re: IRC adv 5051 Error

Thanks for the instructions. The "Saddle Stitch Position Adjustment" only shifts the fold +/- 2mm on the page; however, the staple is consistently 1/8" from the fold. Also, the "Saddle Stitcher Staple Repositioning" has no effect. Is there a way to adjust the position of the saddle stitch to be directly on the fold?

[teckat]

Re: IRC adv 5051 Error

Thanks for the instructions. The "Saddle Stitch Position Adjustment" only shifts the fold +/- 2mm on the page; however, the staple is consistently 1/8" from the fold. Also, the "Saddle Stitcher Staple Repositioning" has no effect. Is there a way to adjust the position of the saddle stitch to be directly on the fold?

👀
Did u read pdf on adjusting the Fold_?

[w0179651]

Re: IRC adv 5051 Error

As always, thanks for saving the day teckat . [facepalm] didn't see the pdf. [double facepalm] didn't know there were two PCBs with dip switches.

[teckat]

Re: IRC adv 5051 Error

As always, thanks for saving the day teckat . [facepalm] didn't see the pdf. [double facepalm] didn't know there were two PCBs with dip switches.

welcome
Thanks_Pizza Man .jpg