[Jamming] IR3045

[akm]

Dear ,CopyTech Team

i face a problem with ir3045 it have jam code 010d when i make two-sided copy if i make 10 copies it passes 2 copies and make jam



thanks
akm

[teckat]

Re: IR3045

Dear ,CopyTech Team

i face a problem with ir3045 it have jam code 010d when i make two-sided copy if i make 10 copies it passes 2 copies and make jam



thanks
akm

Check the One-Way on the back of the A1 unit. ( located on the Right Door) If the One-way is slipping it could cause intermittent 010D Jams. Replace if needed, FU5-3018-000.







CHECK!!!!!!!!!!!!!!!

Jam code 010D only when running duplex copies.


The problem has been found to be caused by the duplex/feed sensor PI 17 becoming dirty. The sensor is located in the transfer roller housing in the image below. It is called the duplexing internal guide in the parts book. One half of this unit is found on figure140 right door assembly. The other half is found on figure 141, paper feeder frame assembly.

There is an opening between the two plastic guides in this assembly. Toner drops down and clogs the eye of the sensor.
To access the sensor open the right door and remove the silver screw shown in the image below.You will need to use a stubby screw driver.

Once the screw has been removed the two plastic housings can be separated and the sensor is clearly visible. It can be cleaned or replaced. The part number for the sensor is FK2-0149-000. The part number for the flag is FC5-0657-000, duplexing feeder sensor flag. The part number for the sensor flag spring is FC5-0658-000, torsion spring.

After cleaning the sensor it can be checked using the I/O mode. Service mode > Copier > I/O > DC CON > screen 3 of 5 P021 bit # 2.

[Rachid.Akli]

Re: IR3045

Dear ,CopyTech Team

i face a problem with ir3045 it have jam code 010d when i make two-sided copy if i make 10 copies it passes 2 copies and make jam



thanks
akm

Hello,

010d is a delay jam at PS17.
Using the attached figure, indicate the position of the jam.

Rachid.

Position of sensors.pdf

[akm]

Re: IR3045

Check the One-Way on the back of the A1 unit. ( located on the Right Door) If the One-way is slipping it could cause intermittent 010D Jams. Replace if needed, FU5-3018-000.







CHECK!!!!!!!!!!!!!!!

Jam code 010D only when running duplex copies.


The problem has been found to be caused by the duplex/feed sensor PI 17 becoming dirty. The sensor is located in the transfer roller housing in the image below. It is called the duplexing internal guide in the parts book. One half of this unit is found on figure140 right door assembly. The other half is found on figure 141, paper feeder frame assembly.

There is an opening between the two plastic guides in this assembly. Toner drops down and clogs the eye of the sensor.
To access the sensor open the right door and remove the silver screw shown in the image below.You will need to use a stubby screw driver.

Once the screw has been removed the two plastic housings can be separated and the sensor is clearly visible. It can be cleaned or replaced. The part number for the sensor is FK2-0149-000. The part number for the flag is FC5-0657-000, duplexing feeder sensor flag. The part number for the sensor flag spring is FC5-0658-000, torsion spring.

After cleaning the sensor it can be checked using the I/O mode. Service mode > Copier > I/O > DC CON > screen 3 of 5 P021 bit # 2.

many thanks eng.techat for your reply i will tomorrow make these checks

[akm]

Re: IR3045

Hello,

010d is a delay jam at PS17.
Using the attached figure, indicate the position of the jam.

Rachid.

[ATTACH]18060[/ATTACH]

many thanks eng.Rachid.Akli for your reply