Canon IR3045 E110-0001

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • skibum
    Independent Service Tech
    Site Contributor
    100+ Posts
    • Apr 2009
    • 231
    #1

    [Error Code] Canon IR3045 E110-0001

    Originally this machine had spots. I pulled the drum and developer units and inspected and cleaned the excess toner from the developer unit and drum unit. Reinstalled and now I have this code. Came in a 2nd time to replace the foam seal with new (Tec-Pub parts) upgraded seal and additional auxiliary seal to prevent toner spilling from the hopper. Cleaned the interior cavity of all toner. Verified the shutter (laser) linkage is working and activated when the right door is shut.

    It appears the laser is dead?

    Does anyone have any ideas?


    Thanks
    Tags: None
    • teckat
      Field Supervisor

      Site Contributor
      10,000+ Posts
      • Jan 2010
      • 16083
      #2
      Re: Canon IR3045 E110-0001

      Originally posted by skibum
      Originally this machine had spots. I pulled the drum and developer units and inspected and cleaned the excess toner from the developer unit and drum unit. Reinstalled and now I have this code. Came in a 2nd time to replace the foam seal with new (Tec-Pub parts) upgraded seal and additional auxiliary seal to prevent toner spilling from the hopper. Cleaned the interior cavity of all toner. Verified the shutter (laser) linkage is working and activated when the right door is shut.

      It appears the laser is dead?

      Does anyone have any ideas?


      Thanks


      If the Developer Unit Connector was removed with the Main Power Switch on it may have blown the DC Controller resulting in an E110 code / could cause fuse to blow on DC PCB board
      FU1.JPG check this fuse & or others (continuity)



      this grounding plate causes weird issues when not in contact as shown

      Make sure that the grounding spring for the steel registration roller is making contact with the roller. If not, Re-form the spring so that it makes contact with the roller
      **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • canonbundy
          Senior Tech

          500+ Posts
          • Jun 2012
          • 607
          #3
          Re: Canon IR3045 E110-0001

          Originally posted by skibum
          Originally this machine had spots. I pulled the drum and developer units and inspected and cleaned the excess toner from the developer unit and drum unit. Reinstalled and now I have this code. Came in a 2nd time to replace the foam seal with new (Tec-Pub parts) upgraded seal and additional auxiliary seal to prevent toner spilling from the hopper. Cleaned the interior cavity of all toner. Verified the shutter (laser) linkage is working and activated when the right door is shut.

          It appears the laser is dead?

          Does anyone have any ideas?


          Thanks
          Check the connection of the 3 pin connector from the LU to the Rear Frame (under the Toner Drive assy) also the connection of the same 3 pin connector on the Back side (remove rear cover) of the Rear Frame - for some reason they actually work loose.

            Comment

            • skibum
              Independent Service Tech
              Site Contributor
              100+ Posts
              • Apr 2009
              • 231
              #4
              Re: Canon IR3045 E110-0001

              Sound like tech error. I did unplug the dev unit while the main switch was on. Do you know what the fuse specs are?
              Thanks,

              Jerry

                Comment

                • teckat
                  Field Supervisor

                  Site Contributor
                  10,000+ Posts
                  • Jan 2010
                  • 16083
                  #5
                  Re: Canon IR3045 E110-0001

                  Originally posted by skibum
                  Sound like tech error. I did unplug the dev unit while the main switch was on. Do you know what the fuse specs are?
                  Thanks,

                  Jerry
                  no/ do a continuity test
                  check 24v connections

                  what pub had info on new seals ???
                  was that the one from 2008 ??
                  SEAL--TP08 170.pdf
                  **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                    Comment

                    • skibum
                      Independent Service Tech
                      Site Contributor
                      100+ Posts
                      • Apr 2009
                      • 231
                      #6
                      Re: Canon IR3045 E110-0001

                      Originally posted by teckat
                      no/ do a continuity test
                      check 24v connections

                      what pub had info on new seals ???
                      was that the one from 2008 ??
                      [ATTACH]19079[/ATTACH]
                      Yes, that was the tech pub.
                      Thanks for your help. I will be going back to test Monday morning and will follow up with what I find.

                        Comment

                        Previous template Next
                        Working...