irc3380i

[akm]

Dear CopyTechTeam,

Please i need your help i have the copier irc 3380i from one week i change the transfer cleaning ass and the m/c works good and afterthat the customer tell me that the m/c gives a white paper and after made check i found the transfer cleaning ass squeezed and press on the ITB and donot allow it to rotate so the copies are white and the body of ITB is broken at installation base of the transfer cleaning ass so i need to know why the blade became so and the right method of installation of transfer cleaning ass

Thanks
Akm

[teckat]

Re: irc3380i

Dear CopyTechTeam,

Please i need your help i have the copier irc 3380i from one week i change the transfer cleaning ass and the m/c works good and afterthat the customer tell me that the m/c gives a white paper and after made check i found the transfer cleaning ass squeezed and press on the ITB and donot allow it to rotate so the copies are white and the body of ITB is broken at installation base of the transfer cleaning ass so i need to know why the blade became so and the right method of installation of transfer cleaning ass

Thanks
Akm

================================================== ==========
1-u need to remove the ITB UNIT first------
2-then replace ITB cleaning unit

You forgot to Lube the blade NOT IN MANUAL
The part number for the ITB cleaning blade lubricant is TKN-0480-000

Black band sequence
If continuous print is carried out while there is no toner being sent on to the ITB cleaning blade, the blade may bend backwards. This sequence feeds non-transferred toner to the cleaning blade in order to prevent this problem.
1. Timing
- When belt rotation is performed after 1,000 sheets printing.
2. Sequence details
After image formation in the normal sequence, a black band (half-tone pattern) is formed over the total width of the ITB, for a length of 10mm, with density FFh. Once the black band clears the secondary transfer roller,
secondary transfer outer roller cleaning (see Note) is performed.
Further, once the black band is formed, the cumulative counter resets to the default (0).
NOTE-Negative bias (TR2 signal) is applied to the secondary transfer outer roller to prevent rear soiling of the print paper, and this creates a difference in electro-potential between the ITB and the roller. As a result, residual
negative toner sticking to the secondary transfer outer roller returns to the ITB and is collected in the cleaning unit by the ITB cleaning blade




READ---------
ITB .pdf

extra note


After Replacing the Secondary Transfer Roller
Upon replacement to the new secondary transfer outer roller, attachment of the rubber component of
the secondary transfer roller onto the ITB belt causes a white spot image.
In order to prevent this, at replacing the secondary transfer outer roller to the new one, coating of toner
onto the surface of the roller is required.

When replacing the secondary transfer outer roller, execute the service mode below:
- COPIER > FUNCTION > TNR-COAT
Coating of the Y toner onto the secondary transfer roller

[Ron314]

Re: irc3380i

Dear CopyTechTeam,

Please i need your help i have the copier irc 3380i from one week i change the transfer cleaning ass and the m/c works good and afterthat the customer tell me that the m/c gives a white paper and after made check i found the transfer cleaning ass squeezed and press on the ITB and donot allow it to rotate so the copies are white and the body of ITB is broken at installation base of the transfer cleaning ass so i need to know why the blade became so and the right method of installation of transfer cleaning ass

Thanks
Akm

Are you needing toilet paper?



314159265

[teckat]

Re: irc3380i

Are you needing toilet paper?



314159265

[akm]

Re: irc3380i

================================================== ==========
1-u need to remove the ITB UNIT first------
2-then replace ITB cleaning unit

You forgot to Lube the blade NOT IN MANUAL
The part number for the ITB cleaning blade lubricant is TKN-0480-000

Black band sequence
If continuous print is carried out while there is no toner being sent on to the ITB cleaning blade, the blade may bend backwards. This sequence feeds non-transferred toner to the cleaning blade in order to prevent this problem.
1. Timing
- When belt rotation is performed after 1,000 sheets printing.
2. Sequence details
After image formation in the normal sequence, a black band (half-tone pattern) is formed over the total width of the ITB, for a length of 10mm, with density FFh. Once the black band clears the secondary transfer roller,
secondary transfer outer roller cleaning (see Note) is performed.
Further, once the black band is formed, the cumulative counter resets to the default (0).
NOTE-Negative bias (TR2 signal) is applied to the secondary transfer outer roller to prevent rear soiling of the print paper, and this creates a difference in electro-potential between the ITB and the roller. As a result, residual
negative toner sticking to the secondary transfer outer roller returns to the ITB and is collected in the cleaning unit by the ITB cleaning blade




READ---------
[ATTACH]20514[/ATTACH]

extra note


After Replacing the Secondary Transfer Roller
Upon replacement to the new secondary transfer outer roller, attachment of the rubber component of
the secondary transfer roller onto the ITB belt causes a white spot image.
In order to prevent this, at replacing the secondary transfer outer roller to the new one, coating of toner
onto the surface of the roller is required.

When replacing the secondary transfer outer roller, execute the service mode below:
- COPIER > FUNCTION > TNR-COAT
Coating of the Y toner onto the secondary transfer roller

Dear Eng.Techat

many thanks for your knowledge ,but i have a question if i relube the transfer cleaning ass it will work good again ?

[akm]

Re: irc3380i

Are you needing toilet paper?



314159265

save it for yourself for benefitting you

[Rachid.Akli]

Re: irc3380i

Dear CopyTechTeam,

Please i need your help i have the copier irc 3380i from one week i change the transfer cleaning ass and the m/c works good and afterthat the customer tell me that the m/c gives a white paper and after made check i found the transfer cleaning ass squeezed and press on the ITB and donot allow it to rotate so the copies are white and the body of ITB is broken at installation base of the transfer cleaning ass so i need to know why the blade became so and the right method of installation of transfer cleaning ass

Thanks
Akm

The correct abbreviation for the word assembly is ass'y. Ass is a vulgare word in english.

Rachid.

[vamoursly]

Re: irc3380i

The correct abbreviation for the word assembly is ass'y. Ass is a vulgare word in english.

Rachid.

Ass is actually either a donkey, or an Americanism; The Queens English is Arse, but we are digressing.....

[teckat]

Re: irc3380i

Rhymes with ARSE

farce, parse, sparse

[vamoursly]

Re: irc3380i

Rhymes with ARSE

farce, parse, sparse

Class?

[akm]

Re: irc3380i

Are you needing toilet paper?



314159265

thanks
save it for you