ir 2318

[pulkit jain]

ir 2318 is not giving accurate margin from all sides (means it cut the print from all side in any paper size) there is no error code

or

if an A4 size paper print is given with a margin of 1 inch from all sides it not print according to that

please rply fast

it is urgent

[teckat]

Re: ir 2318

ir 2318 is not giving accurate margin from all sides (means it cut the print from all side in any paper size) there is no error code

or

if an A4 size paper print is given with a margin of 1 inch from all sides it not print according to that

please rply fast

it is urgent

]]]]]]]]]]]]]]]]]]]]]]]]]

Network prints ?
Glass copies ?
ADF copies ?

check Cassette Size Sensor
SW.JPG

The size of the paper in the cassette is detected by the DC controller PCB when the user changes the position of the cassette paper size lever.
When the cassette is inserted in the iR host machine, the paper size lever pushes the paper size switches provided in the iR host machine to allow the DC controller PCB to detect presence of the cassette and the size of paper.
Paper size switches are arranged as shown below. Paper sizes are determined by the combinations of the switches pushed by the paper size lever.

SW1.JPG
SW2.JPG


Image margin (leading edge) 3.0 -/+1.5 mm
Image margin (trailing edge) 5.0 -/+2.0 mm
Image margin (left/right) left edge: 3.0 -/+2.0 mm
right edge: 0.5 mm or more

[pulkit jain]

Re: ir 2318

the problem occurs from every source i.e. network, glass, and adf

[copy_suhail]

Re: ir 2318

What about manual feed same thing???

[teckat]

Re: ir 2318

the problem occurs from every source i.e. network, glass, and adf

----------------------------

does the Printer READ(on Control Panel) the correct size of all the cassettes when inserted in it-
<Cassette>
- Check whether the cassette is installed properly. Check whether the paper size is set properly.
- Check whether the same symptom occurs when the cassette is replaced with the cassette verified to be normal.
- Check whether the middle plate of the cassette moves smoothly.
- Check whether it is deformed.
- Check whether the side and rear alignment plates are adjusted properly

<Service Mode>
Method of entering the service mode]
Press the Additional Functions key and # key, then enter the service mode.
[Method of operation the service mode]
Select the service menu using the upper/lower/left/right keys and OK key.

- Check whether various adjustment values are the same as those printed on the service label.
- Check whether the output between CIS channels has been corrected.
(Service mode>Test>Scanner test)>CS Output Test)
- Check whether the read position has been adjusted properly. (Stream reading: Only when the ADF is installed)
(Service mode>Test>Scanner test)>CS Position Test)



Make the following adjustments:
- Correction of output between CIS channels
1) Enter the service mode.
Sequentially press the Additional Functions, # key on the operation panel.
2) Using the upper/lower arrow keys on the operation panel, select "Test".
3) Press the OK key.
4) Using the upper/lower arrow keys on the operation panel, select "Scanner test".
5) Press the OK key.
6) Using the upper/lower arrow keys on the operation panel, select "CS Output Test".
7) Press the OK key.
8) Select "Yes" and then press the OK key.
After completion of the above steps, contact sensor output correction will be performed and parameters will be set automatically.
- Read position adjustment (Stream reading: Only when the ADF is installed)
1) Enter the service mode.
Sequentially press the Additional Functions, # key on the operation panel.
2) Using the upper/lower arrow keys on the operation panel, select "Test".
3) Press the OK key.
4) Using the upper/lower arrow keys on the operation panel, select "Scanner test".
5) Press the OK key.
6) Using the upper/lower arrow keys on the operation panel, select "CS Position Test".
7) Press the OK key.
8) Select "Yes" and press the OK key.
The optical system starts scanning. Several seconds later,automatic adjustment of the reading position finishes and "OK" appears.

Enter the service mode
Service's Choice
These setting items are for image adjustment in printer assembly and for special mode for the field-related measures.
Print Position / Initial setting/ Range of setting/ Function

Top-Bypass /50 /0 to 100, /one unit=0.1mm/Top registration adjustment (manual paper feed tray)
Top-Tray /50 /0 to 100, /one unit=0.1mm /Top registration adjustment (cassette)
Top-Duplex /50 /0 to 100, /one unit=0.1mm /Top registration adjustment (duplex unit)
Left-Bypass /100 /0 to 200, /one unit=0.1mm/Left-end registration adjustment (manual paper feed tray)
Left-Tray1 /100 /0 to 200, /one unit=0.1mm /Left-end registration adjustment (cassette 1)
Left-Tray2 /100 /0 to 200, /one unit=0.1mm /Left-end registration adjustment (cassette 2)
Left-Tray3 /100 /0 to 200, /one unit=0.1mm /Left-end registration adjustment (cassette 3)
Left-Tray4 100 /0 to 200, /one unit=0.1mm /Left-end registration adjustment (cassette 4)
Left-Duplex 100 0 to 200, one unit=0.1mm /Left-end registration adjustment (duplex unit)




Now Buy a SERVICE MANUAL