signal cable for canon ir7095 finisher

[cdvidaceiba]

hi , can anyone help me with the part number of the signal cable for finisher canon ir7095 , is the coaxial cable that connects the finisher with the main unit .

is this a simple coaxial cable or the machinne just work with the canon specific cable? . i did buy a copier to a provider in the US i brought it to Honduras long in coming 4 weeks and the cable is missing , i cannot sell the machinne with the finisher not working ....


thanks in advance for your help

[teckat]

Re: signal cable for canon ir7095 finisher

hi , can anyone help me with the part number of the signal cable for finisher canon ir7095 , is the coaxial cable that connects the finisher with the main unit .

is this a simple coaxial cable or the machinne just work with the canon specific cable? . i did buy a copier to a provider in the US i brought it to Honduras long in coming 4 weeks and the cable is missing , i cannot sell the machinne with the finisher not working ....


thanks in advance for your help

-----------------------------------------------------
Finisher-V1
Saddle Finisher-V2

READ-----ARCNET Connections.pdf
Finisher V1_Saddle Finisher V2--INSTALL.pdf



Arcnet Cable / FK2-1771-000.
CABLE, GROUNDING Strap/ FK2-0157-000
T-CONNECTOR/ WS6-5200-000




The finisher functions do not appear available on the display of the imageRUNNER.

The Arcnet Cable is attached with T-connectors and terminators on both ends.
Make sure each end of the of the ARCNET cable is terminated with the provided terminators.
++ U need the Braided Ground Strap on the finisher

When connecting the imageRUNNER 7105 / 7095 / 7086 Series main engine to its delivery accessories (ex. Finisher V1 / Saddle Finisher V2), the Signal Cable, T-Shape Connector and Terminator must be configured correctly.

If an improper connection is made (ex: connecting the signal cable directly to the main body without attaching it to the T-Shape connector or forgetting to attach the terminator to the end of the T-Shape connector), the following error codes can occur:

E500: Finisher Communication Fault.
E711: Communication error has occurred between the Main Engine and its Delivery Accessories.




20526.jpg


First, confirm the following steps:

1) Check if the finisher version is listed in service mode COPIER>DISPLAY>SORTER

2) Check if the finisher is registered in service mode COPIER>OPTION>ACCPST-D

3) Check your ARCNET cables for T-Conections and Terminators on the imageRUNNER and the Finisher.

If your display does not show any version, and your ACCPST-D shows the finisher is attached, try the following steps:

1) Set the value listed in the ACCPST-D to "00", press OK

2) Exit service mode, power off the imageRUNNER, and power off the Finisher.

3) Disconnect the ARCNET cable from the imageRUNNER only.

4) Power on ONLY the imageRUNNER.

5) Check COPIER>OPTION>ACCPST-D (At this point the finisher should no longer be listed)



6) Power off the imageRUNNER

7) Confirm BOTH the imageRUNNER and the finisher have T-Connectors and terminators.

8) Power on the finisher, then power on the imageRUNNER (Note: Power on sequence is important.)

9) Check COPIER>OPTION>ACCPST-D The value should be listed as "01" for the finisher. If the ACCPST-D lists the finisher as "00", try setting to "01", then press OK. (Note: If you have other ARCNET devices attached they will be listed, too, assuming you have connected the ARCNET cables with T-Connectors and have terminated the last device.)

10) Check COPIER>DISPLAY>SORTER Now you should see the finisher listed and the finisher functions available.
22121.jpg

[cdvidaceiba]

Re: signal cable for canon ir7095 finisher

thanks teckat , exelent reply , i just got a question , due to i cant get a original canon cable here in my country , can i use a common ARCNET cable and T connectors ? or maybe can i make the cable??


thanks in advance

[teckat]

Re: signal cable for canon ir7095 finisher

thanks teckat , exelent reply , i just got a question , due to i cant get a original canon cable here in my country , can i use a common ARCNET cable and T connectors ? or maybe can i make the cable??


thanks in advance

----------------------------------------------------
have u tried to search online ?? (they are available)
[FK2-1771-000] - CABLE - Attachment Cable - Genuine Canon Part



ARCnet Cable - FK2-1771-000 ( No alternative currently available that I know of)

'T' Piece connector- WS6-5200-000 (Canon) - or UK-PART-015
Terminator WS6-5201-000 (Canon)- or UK-PART-016

(No alternative currently available that I know of)

[cdvidaceiba]

Re: signal cable for canon ir7095 finisher

ok thanks i will try this options you gave me


really apreciate your help


thanks again

[sham.panhale]

Re: signal cable for canon ir7095 finisher

Halo ,

I am also faceing problem from last six months.
I am from india . I googled for the arcnet cableing . And I found that In arcnet you can use RG-62U 93ohm male to male cable .
Have to tried to search in ur local market no one even know what is the cable is .
Finally I brought on from ebay.com (From US) also t-connectors. But Sad thing is I am still looking for the 93ohm Bnc Terminator.

For your information Sending you a ebay link

IBM Sytle RG62U 93 Ohm BNC Male to Male Cable 2 Ft | eBay

You Should Buy 1Nos - Male to male cable , 2Nos - t-Connectors , 2Nos - 93ohm Terminator.

I hope u understand what i wrout . English is not my mother language.

thanks teckat , exelent reply , i just got a question , due to i cant get a original canon cable here in my country , can i use a common ARCNET cable and T connectors ? or maybe can i make the cable??


thanks in advance