have 3200 pcb board out

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rdc
    Technician

    50+ Posts
    • May 2013
    • 53

    #1

    have 3200 pcb board out

    Have pcb board out of ir 3200,,found fuse 27 bad,,its 60v/3amp can not find a replacement ,,any ideas, thanks for any advice..
  • SCREWTAPE
    East Coast Imaging

    Site Contributor
    2,500+ Posts
    • Jan 2009
    • 3396

    #2
    Re: have 3200 pcb board out

    Originally posted by rdc
    Have pcb board out of ir 3200,,found fuse 27 bad,,its 60v/3amp can not find a replacement ,,any ideas, thanks for any advice..
    Well this is your only option. Replace it

    Comment

    • northernlife
      Senior Tech

      500+ Posts
      • Sep 2011
      • 847

      #3
      Re: have 3200 pcb board out

      Fuses blow for a reason

      Comment

      • Herrmann
        Senior Tech

        Site Contributor
        500+ Posts
        • Jan 2006
        • 792

        #4
        Re: have 3200 pcb board out

        The Voltage is not relevant, only the Ampererage rules, so every Fuse which fits mechanically and a rate of 3 Amps will do the Trick. Just solder wires on it, isolate it thoroughly and solder the wires on the place where the blown fuse was.
        If sometimes you feel a little useless, offended and depressed always remember that you were once the fastest and most victorious sperm of hundreds of millions!

        Comment

        • teckat
          Field Supervisor

          Site Contributor
          10,000+ Posts
          • Jan 2010
          • 16083

          #5
          Re: have 3200 pcb board out

          Originally posted by rdc
          Have pcb board out of ir 3200,,found fuse 27 bad,,its 60v/3amp can not find a replacement ,,any ideas, thanks for any advice..
          ---------------------------------------
          DC Fuse PCB Assembly /FG3-2337-030
          u also need to replace the DUPLEX DRIVER PCB=FG6-9671-000
          it's the Duplex driver pcb that shorts out the
          #27 Fuse on Fuse pcb.
          this is a known issue on these models


          image RUNNER C3200


          How to troubleshoot the DC-fuse PCB or a missing voltage in the machine.

          When an over current or a short to ground occurs in the machine such as a motor binding or a wire shorted to the frame of the machine, a fuse on the DC-fuse PCB should open to prevent damage to the machine.
          The DC-fuse PCB is located in the rear lower left of the machine mounted on the DC-power supply. The circuit diagram for the power
          distribution is found on page 105 & 106 of the technical reference guide.
          The fuse, voltage, connectors, and the destination of the voltage is listed below.

          Fuse Voltage Connector Destination Connector

          3.3 Volts DC have pink wires

          FU11 3.3vdc J59-1 Power distribution PCB J1502-1
          FU11 3.3vdc J59-2 Power distribution PCB J1502-2
          FU13 3.3vdc J60-3 Power distribution PCB J1501-3
          FU13 3.3vdc J60-4 Power distribution PCB J1501-4
          FU14 3.3vdc J61-5 Fax G3-G4 J560-3
          FU14 3.3vdc J61-6 Fax G3-G4 J560-4
          FU15 3.3vdc J61-7 Fax G3-G4 J560-6
          FU22 3.3vdc J64-9 DC controller J100-9
          FU22 3.3vdc J64-10 DC controller J100-10

          5 Volts DC have brown wires

          FU16 5vdc J61-13 Fax G3-G4 J560-11
          FU17 5vdc J60-1 Power distribution PCB J1501-1
          FU17 5vdc J61-11 Fax G3-G4 J560-9
          FU17 5vdc J61-12 Fax G3-G4 J560-10
          FU23 5vdc J71-5 DC controller J106-1
          FU27 5vdc J68-3 Duplex delivery PCB J440-3

          12 Volts DC have orange wires

          FU12 12vdc J59-5 Power distribution PCB J1502-5
          FU18 12vdc J60-8 Power distribution PCB J1501-8
          FU31 12vdc J64-7 DC controller J100-7
          14 volts DC
          FU32 14vdc J65-1 NO output

          24 Volts DC have red wires

          FU20 24vdc J62-1 H3 Fixing unit J802-4
          FU21 24vdc J64-1 DC controller J100-1
          FU21 24vdc J64-2 DC controller J100-2
          FU24 24vdc J74-1 Power distribution PCB J1509-2
          FU24 24vdc J66-1 Fax PCIP J559-1
          FU25 24vdc J67-2 Reader J565-1
          FU25 24vdc J67-3 Reader J565-2
          FU26 24vdc J68-1 Duplex delivery PCB J440-1
          FU28 24vdc J70-1 HV2 sub PCB J91-1
          FU29 24vdc J70-3 Drum ITB motor J93-1
          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

          Comment

          Working...