[Misc] IRC1021 Image Displacement/Out of Focus

[Tuga]

HI

I have a irc1021 with Image Displacement / Out of Focus and I can not adjust.
can someone help me?

thank you

[vamoursly]

Re: IRC1021 Image Displacement/Out of Focus

Is the displacement on a single colour, printing or scanning?

First thing to check are the contacts were the consumables sit, they can break given enough force by end users?

V

[teckat]

Re: IRC1021 Image Displacement/Out of Focus

HI

I have a irc1021 with Image Displacement / Out of Focus and I can not adjust.
can someone help me?

thank you

try to first remove & Re-seat the laser unit.

[teckat]

Re: IRC1021 Image Displacement/Out of Focus

Is the displacement on a single colour, printing or scanning?

First thing to check are the contacts were the consumables sit, they can break given enough force by end users?

V

---------------------------------

issue can occur if the main drive gears in the machine or in the main drive assembly are out of alignment.

see pdf------------

Colors are Mis-Registered on Prints and Copies.pdf

[northernlife]

Re: IRC1021 Image Displacement/Out of Focus

Can also enable "calibration at startup" it fixed one of these for me. can also run an auto grab, that as well fixed another machine. YMMV

[Tuga]

Re: IRC1021 Image Displacement/Out of Focus

HI
How enable "calibration at startup"?

I already checked the lazer.

thanks

[teckat]

Re: IRC1021 Image Displacement/Out of Focus

HI
How enable "calibration at startup"?

I already checked the lazer.

thanks

-----------------------------
1) Press (Main Menu).
2) Press the right Any key to select <Additional Func>.

Adjustment/Cleaning

select to "ON"
First Calibration OFF*/ON

Auto Gradation Adjustment
CAUTION:
Make sure to set a test print correctly. If a test print cannot be read correctly, the adjustments of gradation, density and color cannot be performed appropriately-
1) Open the feeder.
2) Clean the copyboard glass of the host machine.
3) Set A4 or LTR paper on the cassette. (Refer to the cassette settings.)
4) Close the feeder.
5) Specify the full adjustment in additional function mode.
[Additional Func] > [Adjustment/Cleaning] > [Auto Gradation Correction] > [Full Correction]
6) When 'Test Print1' is displayed, press [OK].
Test Print 1 is output. (It takes approx, 3min.)
7) Follow the instruction on a control panel and set the test print 1 on the copyboard glass.
8) Close the feeder.
9) Press [OK].
Test Print 1 is read.
10) When 'Test Print 2' is displayed, press [OK].
Test Print 2 is displayed.
11) Follow the instruction on a control panel and set the test print 2 on the copyboard glass.
12) Close the feeder.
13) Press [OK].
Test Print 2 is read.
14) When the auto adjustment window is displayed, remove the test print 2 from the copyboard glass.
15) Exit [Additional Func].

Dirt Sensor Control
Dust correction
When dust is detected, the correction of removing the dust is automatically performed based on the scanned data.
However, when a document does not have a margin or it has an image on the margin, the machine determines that dust is adhered to the scanning glass surface, which may cause incorrect correction to be performed. In such a case, disabling of the correction can be set in the user mode.
Adjustment/Cleaning > Automatic correction of feeder dust
ON: Perform automatic correction (initial setting)
OFF: Do not perform automatic correction.

Auto Gradation Correction Control
Overview
Auto gradation correction control is to stabilize the gradation density features of image.
To execute, select [Adjustment/Cleaning > Auto Gradation Correction] in additional function mode.
It has the following 3 correction controls.

Full Correction (PASCAL) This correction outputs a test pattern and the reader scans its gradation
density to adjust the gradation. Number of test pattern sheet=2
Type of test pattern-
1st sheet: T-MIC
2nd sheet: high/low screen rulings

Quick Correction -This correction adjusts the gradation by means of D-half control instead
of outputting a test pattern. Number of test pattern sheet=0

Copy Image Correction -This correction outputs a test pattern and the reader scans its gradation to
mainly adjust the gradation of copy image. Number of test pattern sheet=1
Type of test pattern-
T-MIC