[Misc] canon ir 2525 scanning from adf only LTR size and not A/4 size

[pramod]

Hello Friends,
I got some old machines ir 2525. I can scan and copy A/4 size from platen,but from ADF only LTR size is sensed and not A/4 size. So please give some solution. I am from India and these machines are imported from USA.

[elamurugu]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

ADF pcb have paper salection SW. and cheak the service mode-feeder-function seet A4 size.

[spectraindo]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

Go to Service Mode : *- 2 - 8 -* press > till display shows "CLEAR" OK, press > till display shows "TYPE" OK press > till display shows "ASIA" or "SG" OK.
The ADF will detect A4 and A3.

[pramod]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

Thanks for reply , i already tried in service mode, changed country changed model size.There is no sw on ADF pcb. One more thing i noticed if i scan from ADF with network scangear A/4 size is scanned only problem in copier mode . If any other solution ,please reply.

[teckat]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

the following needs to be set in service mode.


SCAN > SCAN SW > SW06 > Bit2 to 1

-----------------------------------------------------------------------
also under >
SYSTEM > SYSTEM Numeric > 057 to 1 or 2 for metric configuration

1: AB configuration

2: A configuration

3: Inch configuration

4: AB / Inch configuration



#SCAN > READER
<194:
ADF special standard-sized paper: LTR mis-identification ready>
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
0: LTR
1: G_LTR
2: A_LTR

<195:
ADF special standard-sized paper: LTR_R mis-identification ready>
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").
0: LTR_R
1: FOOLSCAP
2: OFFICIO
3: E_OFFICIO
4: G_LTR_R
5: A_LTR_R

[pramod]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

Thank You Teckat,
I am out of town as soon as come back and try these solutions, still thank you for your valuable advise .

[Rvale]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

Go to Service Mode : *- 2 - 8 -* press > till display shows "CLEAR" OK, press > till display shows "TYPE" OK press > till display shows "ASIA" or "SG" OK.
The ADF will detect A4 and A3.

Please, don't put service modes on forums, they are supposed to be used by technicians and not users, if you want to help someone send him an email an keep things under control.
even one of your clients, usually the worsts, are looking to save some money and at the end give you a lot of problems just from finding something interesting on the "internet".

[sam costa]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

i also have the same issue, pls can we change this?

[teckat]

Re: canon ir 2525 scanning from adf only LTR size and not A/4 size

i also have the same issue, pls can we change this?

---

the following needs to be set in service mode.


SCAN > SCAN SW > SW06 > Bit2 to 1

-----------------------------------------------------------------------
also under >
SYSTEM > SYSTEM Numeric > 057 to 1 or 2 for metric configuration

1: AB configuration

2: A configuration

3: Inch configuration

4: AB / Inch configuration



#SCAN > READER
<194:
ADF special standard-sized paper: LTR mis-identification ready>
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
0: LTR
1: G_LTR
2: A_LTR

<195:
ADF special standard-sized paper: LTR_R mis-identification ready>
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").
0: LTR_R
1: FOOLSCAP
2: OFFICIO
3: E_OFFICIO
4: G_LTR_R
5: A_LTR_R