colorpass GX300 & imagepress Q2

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • wassem
    Trusted Tech
    • Aug 2012
    • 166

    #1

    colorpass GX300 & imagepress Q2

    i want to ask if the colorpass GX300 and imagepress Q2 have the same software
  • teckat
    Field Supervisor

    Site Contributor
    10,000+ Posts
    • Jan 2010
    • 16083

    #2
    Re: colorpass GX300 & imagepress Q2

    imagePRESS Server T1 / T2 / Q1 / Q2, imagePASS C2 / H1 / J1, ColorPASS GX100 / GX200 / GX300

    "System Updates" are enabled through the RUI for the imagePASS or ColorPASS


    1) Enter the IP ADDRESS of the imagePASS or ColorPASS into the address field of Internet Explorer or other web browser being used.

    2) Click the [CONFIGURE] tab.

    3) Click on [Launch Configure].

    4) You will get a Login Screen. The default password is: Fiery.1




    5) Click on [Server] in the left panel.

    6) Click on [System Update] in the left panel.



    7) Put a check mark next to [Enable System Update] in the right panel.

    8) Select the Day and the time you would like the update to take place and hit APPLY.

    9) Reboot the device to ensure the changes to take effect.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

    Comment

    • wassem
      Trusted Tech
      • Aug 2012
      • 166

      #3
      Re: colorpass GX300 & imagepress Q2

      Originally posted by teckat
      imagePRESS Server T1 / T2 / Q1 / Q2, imagePASS C2 / H1 / J1, ColorPASS GX100 / GX200 / GX300

      "System Updates" are enabled through the RUI for the imagePASS or ColorPASS


      1) Enter the IP ADDRESS of the imagePASS or ColorPASS into the address field of Internet Explorer or other web browser being used.

      2) Click the [CONFIGURE] tab.

      3) Click on [Launch Configure].

      4) You will get a Login Screen. The default password is: Fiery.1




      5) Click on [Server] in the left panel.

      6) Click on [System Update] in the left panel.



      7) Put a check mark next to [Enable System Update] in the right panel.

      8) Select the Day and the time you would like the update to take place and hit APPLY.

      9) Reboot the device to ensure the changes to take effect.

      hi MR Teckat
      ii want to ask if the server not go to the ready or idle state
      this system update can be done or i mean the rui can be loaded (i think it does not called rui but WebTool)

      Comment

      • teckat
        Field Supervisor

        Site Contributor
        10,000+ Posts
        • Jan 2010
        • 16083

        #4
        Re: colorpass GX300 & imagepress Q2

        What exactly is your issue & on what SERVER MODEL




        To access the copier's RUI through Web Tools
        : 1. Open a Web Browser and type in the IP address of the imagePASS to bring up the Fiery Web Tools.
        2. Click Status in Web Tools.
        3. Click the Remote UI button.
        4. This will access the RUI for the connected copier.
        ================================================== ========

        To access the copier's RUI through the Fiery in one step: 1. Open a Web Browser and type in the following URL:
        http://:8080/

        Newer imagePASS Controllers, ColorPASS GX100, and imagePRESS Server Controllers:

        On the newer imagePASS controllers, ColorPASS GX100, and imagePRESS Server controllers, there is a link to launch the RUI on the Home tab of the Web Tools.

        If using the FACI Kit from the RIP/
        To access the RUI from the FACI Kit:
        1. Launch IE.
        2. Enter 10.255.255.2 for the URL.
        3. The RUI on the copier will then display successfully.
        **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • wassem
          Trusted Tech
          • Aug 2012
          • 166

          #5
          Re: colorpass GX300 & imagepress Q2

          Originally posted by teckat
          What exactly is your issue & on what SERVER MODEL




          To access the copier's RUI through Web Tools
          : 1. Open a Web Browser and type in the IP address of the imagePASS to bring up the Fiery Web Tools.
          2. Click Status in Web Tools.
          3. Click the Remote UI button.
          4. This will access the RUI for the connected copier.
          ================================================== ========

          To access the copier's RUI through the Fiery in one step: 1. Open a Web Browser and type in the following URL:
          http://:8080/

          Newer imagePASS Controllers, ColorPASS GX100, and imagePRESS Server Controllers:

          On the newer imagePASS controllers, ColorPASS GX100, and imagePRESS Server controllers, there is a link to launch the RUI on the Home tab of the Web Tools.

          If using the FACI Kit from the RIP/
          To access the RUI from the FACI Kit:
          1. Launch IE.
          2. Enter 10.255.255.2 for the URL.
          3. The RUI on the copier will then display successfully.
          can i use system update to change the language of the controller

          Comment

          • teckat
            Field Supervisor

            Site Contributor
            10,000+ Posts
            • Jan 2010
            • 16083

            #6
            Re: colorpass GX300 & imagepress Q2

            On Printer control panel/-> Scroll to &
            press [Printer] TAB>
            Press [Printer Status/Settings]
            Functions

            On Q2 Print Server Control Panel> scroll to Run Set Up>Language screen > ?
            or-----------------
            Check in Command Work Station/or Web Tools, check under Server Setup.
            Check your Market Region Language selection ?

            Or>>>
            Language Switch Shortcut Key for>>

            imageRUNNER 2270 / 2870 / 3570 / 4570 / 3025 / 3030 / 3035 / 3045 / 5050 / 5055 / 5065 /5070 / 5075 / 5570 / 6570 / 8070 / 9070 / 85+ / 105+ / 7086 / 7095 / 7105 / 3225 / 3230 / 3235 /3245,
            Color imageRUNNER C3170 / C5870 / C6870 / C2880 / C3380 / C2550 / C3080 / C3480 / C4080 / C4580 / C5180 / C5185 / C5058 / C5068,

            & All imagePRESS Series

            Language Switch Shortcut Key

            How it is configured and how is it used

            The Language Switch Shortcut, when enabled, is displayed next to the 'System Monitor' button on the device LCD screen as shown in the image below. It allows users to walk up to the device to quickly and easily switch the LCD display to their desired language. This shortcut can be useful if, for example, the device is located in a hotel's business center where people from all over the world want to access the device.



            I. Configuring the Language Switch Shortcut Key

            1. Go to Additional Functions / Common Settings / Language Switch and the following screen will appear:



            2. Press ON

            3. Select a default language

            4. Select 'Display Shortcut Key' (when this option is selected the button will change from gray to teal in color)

            5. Press OK

            Using the Language Switch Shortcut Key

            When a user wants to change the display language they have to click on the Shortcut Key, which will bring them to the 'Language Switch' screen.
            From here they select the desired language by highlighting it from the list and press OK. This will return them to the copier main LCD screen where all buttons and text will be displayed in the selected language.
            Last edited by teckat; 07-05-2014, 06:19 PM.
            **Knowledge is time consuming, exhausting and costly for a trained Tech.**

            Comment

            • ofiexpertos
              Technician
              • Nov 2012
              • 10

              #7
              Re: colorpass GX300 & imagepress Q2

              Originally posted by wassem
              hi MR Teckat
              ii want to ask if the server not go to the ready or idle state
              this system update can be done or i mean the rui can be loaded (i think it does not called rui but WebTool)
              Hello,

              Does anyone know where can I find the system software for GX-300 for C5051?

              Thanks in advance.

              Comment

              • Phil B.
                Field Supervisor

                10,000+ Posts
                • Jul 2016
                • 22798

                #8
                Re: colorpass GX300 & imagepress Q2

                Originally posted by ofiexpertos
                Hello, Does anyone know where can I find the system software for GX-300 for C5051? Thanks in advance.
                Not on thread topic


                dead thread for 5years

                start your own damn thread

                Comment

                Working...