[Electrical] IR 5570 wire harness to charge corona

[dan7777]

Does anyone know the part number for the wire harness that plugs into the charge corona assembly? I think it goes to the charge wire cleaning motor. I have a parts book but can not find it.

[northernlife]

Re: IR 5570 wire harness to charge corona

Pretty sure it's FG6-5057-000 but I'm not 100% sure on that, says HV Cable, seems to be about the area of the HV primary block.

Edit: Same part for 5000 series, 5070 series and 5570 series, as the primaries are all the same on these units I would suspect this would be the right part but I'm not 100% sure as said.

[dan7777]

Re: IR 5570 wire harness to charge corona

Pretty sure it's FG6-5057-000 but I'm not 100% sure on that, says HV Cable, seems to be about the area of the HV primary block.

Edit: Same part for 5000 series, 5070 series and 5570 series, as the primaries are all the same on these units I would suspect this would be the right part but I'm not 100% sure as said.

Thank you. If it is the same I think we have a 5000 series copier maybe I can rob while I look.

[teckat]

Re: IR 5570 wire harness to charge corona

Pretty sure it's FG6-5057-000 but I'm not 100% sure on that, says HV Cable, seems to be about the area of the HV primary block.

Edit: Same part for 5000 series, 5070 series and 5570 series, as the primaries are all the same on these units I would suspect this would be the right part but I'm not 100% sure as said.

=========================

you got it ole.jpg



imageRUNNER 5075 / 5065 / 5055 / 5050 / 6570 / 5570 / 5070
part numbers for the Primary, Transfer & Pre transfer HVT end blocks / High voltage connectors





Primary HVT End Block FH2-9243-000 (all models)

Pre Transfer HVT End Block FH2-9248-000 (all models)

Transfer/Separation HVT End Block FG6-5057-000 (all models except iR5075)

Transfer/Separation HVT End Block FM2-9675-000 (only for iR5075)

[northernlife]

Re: IR 5570 wire harness to charge corona

ole ole ole...ole ole....man I can't wait for hockey to start up again :-) Thanks for the confirmation teckat

[vigour]

Re: IR 5570 wire harness to charge corona

You may be looking for this

TECHNICAL PUBLICATION

Page 1 of 2

Details

This Technical Publication is to inform the field of a countermeasure to prevent Error Code E824.

Installation/Service Notes

When the Primary Fan Duct [1] is removed from the equipment the harness for J161D [2] is too short making it verydifficult to disconnect. The harness, over time, will stretch and cause an open circuit. As a result this could causeintermittent E824 codes.Figure 1A harness extension [2] was made to connect to J161D [1]. This will extend the harness making it easier to remove thePrimary Fan Duct.Figure 2Product(s)

imageRUNNER 5070/5570/6570

Number

Subject

Measures to Prevent E824 Codes

Date

April 25, 2007

Page 2 of 2

SERVICING WORK:

1. Open the front cover.2. Open the toner cover3. Remove the two screws and detach the toner supply cover4. Remove the screw and detach the connector cover.5. Connect the fan harness [2] to the connector from the equipment side [1]. (see P-2)Figure 3

Parts / Data FilesDescription Part Number P.C. Page

1 New Cable, Connecting Fan FM3-0074-000 101

[dan7777]

Re: IR 5570 wire harness to charge corona

You may be looking for this

TECHNICAL PUBLICATION

Page 1 of 2

Details

This Technical Publication is to inform the field of a countermeasure to prevent Error Code E824.

Installation/Service Notes

When the Primary Fan Duct [1] is removed from the equipment the harness for J161D [2] is too short making it verydifficult to disconnect. The harness, over time, will stretch and cause an open circuit. As a result this could causeintermittent E824 codes.Figure 1A harness extension [2] was made to connect to J161D [1]. This will extend the harness making it easier to remove thePrimary Fan Duct.Figure 2Product(s)

imageRUNNER 5070/5570/6570

Number

Subject

Measures to Prevent E824 Codes

Date

April 25, 2007

Page 2 of 2

SERVICING WORK:

1. Open the front cover.2. Open the toner cover3. Remove the two screws and detach the toner supply cover4. Remove the screw and detach the connector cover.5. Connect the fan harness [2] to the connector from the equipment side [1]. (see P-2)Figure 3

Parts / Data FilesDescription Part Number P.C. Page

1 New Cable, Connecting Fan FM3-0074-000 101

Hi, Thanks for the reply. But it is the wire harness to the front of the charge corona that plugs in for the charger wire cleaner motor. I just found out this morning they are upgrading to a canon C7260 so now I don't have to worry about it any more. I have had two of them pull the wires out. The connecter is tight and the wires small. Too many pulls and out comes the wires. This 5570 had 3 million copies and many years old.