[Jamming] IR5075 Jamming

[zelotprotos]

ir5075 delivery jam.JPGI got my machine jam at the delivery claw.
I have tried to replace that delivery unit as shown with red line in the attachment with a working one.
So I know the the problem (jam) is caused by this part.
Can anybody guess which part of that delivery unit has broken or not set correctly?

Jam has occurred only when I used FOLIO (21,5 cm x 33 cm) paper.

A4 paper has good result. there is no jamming at all.
Thank your for your attention and helping.

[MrB]

Re: IR5075 Jamming

Hi
Is there a finisher installed on this device

If there is, i do believe that the white drive roller (Next the the flag sensor on the exit) Should NOT be there
Remove that white roller and see how that goes

[zelotprotos]

Re: IR5075 Jamming

Hi
Is there a finisher installed on this device

If there is, i do believe that the white drive roller (Next the the flag sensor on the exit) Should NOT be there
Remove that white roller and see how that goes

No, I don't use finisher.

[Taggerung08]

Re: IR5075 Jamming

1) It kind of looks like your registration is off (paper is crooked). Is that just the angle of the picture? If so check the registration roller, registration gate, and check the paper feed components (weak feed can lead to offset registration).

2) Is this from a print job (originating from a computer) or a copy job??

The paper path is different if it is a print job. The paper will exit the fuser, go down to the duplexing unit and flip the paper before it exits (even on simplex).

[Taggerung08]

Re: IR5075 Jamming

Also what is the specific Jam Code?

[zelotprotos]

Re: IR5075 Jamming

1) It kind of looks like your registration is off (paper is crooked). Is that just the angle of the picture? If so check the registration roller, registration gate, and check the paper feed components (weak feed can lead to offset registration).

2) Is this from a print job (originating from a computer) or a copy job??

The paper path is different if it is a print job. The paper will exit the fuser, go down to the duplexing unit and flip the paper before it exits (even on simplex).

It is from print job and copy job.
I am sure that the problem is caused by that delivery unit ( I have replaced delivery unit from a good machine and all problem solved)

[zelotprotos]

Re: IR5075 Jamming

[QUOTE=Taggerung08;436411]Also what is the specific Jam Code?[/QUO


There is no jam code.

[abb]

Re: IR5075 Jamming

the claw separation get bloked FB5-3625 or FB2-6899 , lubrificate it with blue bottle called "contact universel".
and attention to put the claw inclined for don't scratch the roller.

[Canuck]

Re: IR5075 Jamming

Just like IR5000...replace delivery, and reversing rolls along with bearings and gear with one way in it

[zelotprotos]

Re: IR5075 Jamming

Just like IR5000...replace delivery, and reversing rolls along with bearings and gear with one way in it

Delivery Unit.jpgThis is the delivery that has problem. After replacing it, the problem is resolved.
So I want to repair this unit. Which part of this unit is broken or what's the problem of this unit?

[vigour]

Re: IR5075 Jamming

The solution is in your hands!!!!
There is damage to your lead edge, which means your sep claw has a problem.
Start by changing them

[ARUN MISHRA]

Re: IR5075 Jamming

delivery flaper is cracked in middle .....flapper is black comb type......check its solenoid for adjust.....

[ARUN MISHRA]

Re: IR5075 Jamming

The inside outside delivery flapper (black comb type ) may be cracked in the middle.......change the delivery flapper...