Connecting Canon IR2525 to Jamex 6557 Coin-OP

[doug]

Hi Guys,
I have a Canon IR2525 that I am connecting to a Jamex 6557 coin-op.
I have the Copy Control Interface hooked up from Canon, but need to know how to put the copier under "vendor control" through the service mode.
Has anyone done this before?Please help...
Thank you,
Doug

[jworthington]

Re: Connecting Canon IR2525 to Jamex 6557 Coin-OP

I have haven't done it
Try in service mode scroll to #ACC scroll to Coin enter-1. Hope the works.

[teckat]

Re: Connecting Canon IR2525 to Jamex 6557 Coin-OP

Hi Guys,
I have a Canon IR2525 that I am connecting to a Jamex 6557 coin-op.
I have the Copy Control Interface hooked up from Canon, but need to know how to put the copier under "vendor control" through the service mode.
Has anyone done this before?Please help...
Thank you,
Doug

******:-)For a Coin Box installation
IR2525 _this setting may be in Level 1 or Level 2 > Copier>Option>ACC> CC-SPSW to "1"

Level 1 > Copier>Option>ACC> Coin to "1"
(The LCD will now indicate Please Insert Coins)

The copy control interface cable, sales item #3726B002AA, is installed between J8117 and the device.

[doug]

Re: Connecting Canon IR2525 to Jamex 6557 Coin-OP

******:-)For a Coin Box installation
IR2525 _this setting may be in Level 1 or Level 2 > Copier>Option>ACC> CC-SPSW to "1"

Level 1 > Copier>Option>ACC> Coin to "1"
(The LCD will now indicate Please Insert Coins)

The copy control interface cable, sales item #3726B002AA, is installed between J8117 and the device.

Very good....Thank you! Worked like a charm....
Again, very grateful
Doug

[lcll]

Re: Connecting Canon IR2525 to Jamex 6557 Coin-OP

I'm new so I'm going to tag on to this post. I've got an image runner in "vendor control" mode. i.e. its home screen says "please insert coin". I tried changing ACC to 0 but then it asks for a card.

What setting would take it out of vendor control mode?

[teckat]

Re: Connecting Canon IR2525 to Jamex 6557 Coin-OP

I'm new so I'm going to tag on to this post. I've got an image runner in "vendor control" mode. i.e. its home screen says "please insert coin". I tried changing ACC to 0 but then it asks for a card.

What setting would take it out of vendor control mode?

================================================== =
make sure both selections below are at "0"

ACC>COIN>0 and also ACC>CC-SPSW>0



try and set all below to "0"- power of >on printer
Coin "0"
Card "0"
CC-SPSW "0"
CONTROL "0"



Service Mode > #ACC > Configuration

#ACC

COIN
Coin vendor change
Set the control card set display appearing on the operator station for
vendor use.
0: Control card use
1: Coin vendor use


CARD
Card reader installation setting
Enter a card number to use.
(0 to 9999. One hundred cards are registered with the department ID beginning from the input card number in sequence.)
*1:1,000 cards if option ROM is mounted.
When a card number is entered, the following kinds of management information are initialized:
- Card name (department ID), beginning from the input card number.
- Password associated with the card

CC-SPSW
Control card I/F support setting
Set whether to support the control card I/F (CC-V) or not.
0: Do not support.
1: Support.

COIN
Coin vendor change
Set the control card set display appearing on the operator station for vendor use.
0: Control card use
1: Coin vendor use

CONTROL
Set the PDL printer output control where the control card I/F (CC-V)
is supported.
0: Enable printing without a card mounted.
1: Enable printing with a card mounted in position.