UPGRADING Canon IR105

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Abrantes
    replied
    Re: UPGRADING Canon IR105

    Hi,


    since you don't seem to be a canon's field technician my first advice is to call a good assistance at your area.


    if not possible or too expensive i'd advice you that solving feeding paper jam at IR105 demands knowledge. first, your problem is most caused by paper trays jams, they are not in reverse system but in tray feeding system the most comon cause are rolls, clutchs or sensors. the fault at transfer or detack corona might be also a paper jam cause but in your case it's not the main cause.


    since you have many causes for tray feeding jams you can start by the feed rolls, usually retard rolls cause problems (replace and adjust it and replace all feed rolls at the same time, try other tray) the problem is that if it doesn't solve the problem you will need patience to find it
    if it's not a rolls' problem it'd be a tray clutch problem or a miss paper guide or a dirty sensor or damaged actuator (IR105 has many sensor actuators at paper path) look for registry problems, IR105 has a register clutch and a brake that can hold or retard paper.


    once again, it's very tricky to solve paper jam at IR105, call a good technician

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Any answer please.

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Originally posted by vigour
    you seem to be getting a lot of 0022 jams which is means

    xx22 feed path paper sensor 2 stationary jam (S7)

    You are getting E202 on the same dates as 0022 jams.
    E202 is a no code error, it only shows up in service mode , never on the display.
    This happens when the machine has scanner problems
    1 copyboard is loose---there is a switch in the left rear corner.
    2 bad home position sensor
    3 bad scanner motor
    4 reader controller problems

    Dear vigour

    Thank you very much for your reply.
    I couldn't find the switch you mean on the copyboard, can you point it at attachment picture?.
    Dc2000.jpg


    Also, did you mean by # 2,3, and 4 that I should replace ( PS1 ), ( M5 ), and PCB ?

    Regards.

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Originally posted by Canon345
    On the duplex unit. I feel that a more popular culprit of 2 sided jams is the guide on the left side. The one you open to the left to remove paper. Replace it, you can see that the ribs get worn down by the paper. Also make sure the big guide is intact and not broken along with the two springs being present. This is a must for eliminating two sided jamming.
    Dear Canon345

    Thanks for your reply.

    Dc1999.jpg

    At the attached picture, do you mean I replace all the left guide # 1 ? or just rollers.
    Also, about big right guide # 2 , which spring you mean?, because there are many springs.

    Regards.

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Originally posted by teckat
    [ATTACH=CONFIG]29020[/ATTACH]
    ----------------------------------------------------------------------------------------------------------

    The error codes are grouped as follows according to the items they refer to:
    E000 to E399 error code related to the copier
    E400 to E499 error code related to the ADF
    E500 to E514 error code related to the finisher
    E515 error code related to the inserter
    E518 error code related to the paper folding unit
    E530 to E595 error code related to the finisher
    E5F0 to E5F9 error code related to the saddle stitch assembly
    E601 to E830 error code related to the copier


    When the self diagnostic mechanism has gone ON, the machine may be reset by turning its power switch. This, however, does not apply to E000,
    E001, E002, E003, E004, E005, E013, E020, or E717, indicating a fault which can lead to serious consequences if the machine is reset without removing
    the cause (i.e., melting thermistor, which will overheat the fixing roller, or overflowing of toner from the hopper).
    If the code is from E000 to E003, the power switch will go OFF in about 30 sec if it is turned ON without resetting; in the case of E004, the power
    switch will go OFF in about 3 sec after indicting E000 if the power switch is turned ON without resetting.
    You will have to clear the data in the RAM on the DC controller PCB for the following: E000, E001, E002, E003, E004, E005, E013, E020, and
    E717.

    <Clearing Errors>
    1) Execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
    2) Press the Reset key twice to return to the Copy Mode screen.
    3) Turn off and the on the main power switch.
    Dear teckat
    Thank you very much for your reply.

    You mean my first step is to clear errors?

    Regards.

    Leave a comment:


  • Canon345
    Guest replied
    Re: UPGRADING Canon IR105

    Originally posted by dedode
    Thanks COPIERTEC for your reply.

    Making modifications to Canon IR105 solving the most common continuous problems in this machine.
    As I am one of the users for this machine, I am stuck in to two problems at the moment:
    1- Two side copy Jamming. ( As you gave me a solution for it in this post which I will try it. )
    2- Very slow PDF printing.

    Regards.
    On the duplex unit. I feel that a more popular culprit of 2 sided jams is the guide on the left side. The one you open to the left to remove paper. Replace it, you can see that the ribs get worn down by the paper. Also make sure the big guide is intact and not broken along with the two springs being present. This is a must for eliminating two sided jamming.

    Leave a comment:


  • vigour
    replied
    Re: UPGRADING Canon IR105

    you seem to be getting a lot of 0022 jams which is means

    xx22 feed path paper sensor 2 stationary jam (S7)

    You are getting E202 on the same dates as 0022 jams.
    E202 is a no code error, it only shows up in service mode , never on the display.
    This happens when the machine has scanner problems
    1 copyboard is loose---there is a switch in the left rear corner.
    2 bad home position sensor
    3 bad scanner motor
    4 reader controller problems

    Last edited by vigour; 05-03-2015, 04:29 AM.

    Leave a comment:


  • teckat
    replied
    Re: UPGRADING Canon IR105

    ERROR.jpg
    ----------------------------------------------------------------------------------------------------------

    The error codes are grouped as follows according to the items they refer to:
    E000 to E399 error code related to the copier
    E400 to E499 error code related to the ADF
    E500 to E514 error code related to the finisher
    E515 error code related to the inserter
    E518 error code related to the paper folding unit
    E530 to E595 error code related to the finisher
    E5F0 to E5F9 error code related to the saddle stitch assembly
    E601 to E830 error code related to the copier


    When the self diagnostic mechanism has gone ON, the machine may be reset by turning its power switch. This, however, does not apply to E000,
    E001, E002, E003, E004, E005, E013, E020, or E717, indicating a fault which can lead to serious consequences if the machine is reset without removing
    the cause (i.e., melting thermistor, which will overheat the fixing roller, or overflowing of toner from the hopper).
    If the code is from E000 to E003, the power switch will go OFF in about 30 sec if it is turned ON without resetting; in the case of E004, the power
    switch will go OFF in about 3 sec after indicting E000 if the power switch is turned ON without resetting.
    You will have to clear the data in the RAM on the DC controller PCB for the following: E000, E001, E002, E003, E004, E005, E013, E020, and
    E717.

    <Clearing Errors>
    1) Execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
    2) Press the Reset key twice to return to the Copy Mode screen.
    3) Turn off and the on the main power switch.

    Leave a comment:


  • teckat
    replied
    Re: UPGRADING Canon IR105

    Originally posted by dedode
    Thanks Teckat for you reply.

    But I don't have any problem with the machine except two side copy.
    So, please can you tell which error is related to this issue.

    Regards.



    u mean JAM CONDITION
    see attach link & read pdf below



    JAMS.jpg
    Attached Files
    Last edited by teckat; 05-01-2015, 09:07 PM.

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Thanks Teckat for you reply.

    But I don't have any problem with the machine except two side copy.
    So, please can you tell which error is related to this issue.

    Regards.

    Leave a comment:


  • teckat
    replied
    Re: UPGRADING Canon IR105

    Call for Service/ Buy a Manual/ or Read Below/




    This document provides a list of jam codes for Canon imageRUNNER copiers and document feeders to help with troubleshooting. It includes: 1. An overview of the information displayed for jam codes, including location, date, time, paper size, and source. 2. Tables of jam codes for different copier models (iR105, iR8500, iR7200) and document feeders (DADF-J1, DADF-D1), organized by jam type and associated sensor. 3. Notes on interpreting jam codes for feeder jams on the iR7200/8500/105, with X indicating if it is the first or subsequent page picked

    JAM Descriptions Link
    ================================================== =======================
    Error Codes > Canon > iR105
    ERROR LISTINGS LINK
    ================================================== ========================

    E019=waste toner case is full, or the waste toner case full sensor is faulty.
    E068=error in the high-voltage output to the separation charging assembly.
    E069==error in the high-voltage output to the transfer charging assembly.
    E100=BD PCB is faulty.
    E202=error in the detection of the scanner home position.

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    Because the attachment limited to 10 per post, I attached the rest pictures in this post>
    Attached Files

    Leave a comment:


  • dedode
    replied
    Re: UPGRADING Canon IR105

    I attached the pictures for service mode code errors.
    Also, I noticed that if I change the feeder, two side copy works fine but still with one copy only and not more or it will jam.

    Regards.
    Attached Files

    Leave a comment:


  • teckat
    replied
    Re: UPGRADING Canon IR105

    Originally posted by dedode
    Dear vigour.
    How do I get the code?, because what appeared in the screen is what I attached.

    Regards.
    -------------------
    Image Runners Jam Code List

    disregard Scribd link name is

    301 Moved Permanently

    Leave a comment:


  • teckat
    replied
    Re: UPGRADING Canon IR105

    Originally posted by dedode
    Dear vigour.
    How do I get the code?, because what appeared in the screen is what I attached.

    Regards.

    ================================================== ==========
    are u a tech /// guess not

    codes are in service mode to view

    SEE LINK/ disregard Scribd label

    301 Moved Permanently


    Leave a comment:

Working...