canon ir adv c7065 doubles photos with color

[markndreu]

what can i do to fix it, does someone knows the problem?
please help me because i'm out of mind.

11650958_1007466302604403_1588185937_n.jpg11668089_1007466319271068_1997923048_n.jpg

[teckat]

Re: canon ir adv c7065 doubles photos with color

what can i do to fix it, does someone knows the problem?
please help me because i'm out of mind.

[ATTACH=CONFIG]29648[/ATTACH][ATTACH=CONFIG]29649[/ATTACH]

Check for any broken drum drive gears.
drums have a 4 tooth gear



color displacement, it may be caused by fault of each laser scanning system,
transfer (intermediate transfer/secondary transfer) unit or photosensitive drum drive unit.



did u try --Auto Correct Color Mis-Match

[vigour]

Re: canon ir adv c7065 doubles photos with color

After doing Colour mismatch,
Run ITB-INIT.
You may have to clean up the ITB rollers and possibly change the belt.
Bearings on the Inner Transfer roller seize or break apart

There is usually a missing colour when the drum breaks.
You need to do something about that mottling Cyan

[markndreu]

Re: canon ir adv c7065 doubles photos with color

thanks very much but i see all drum and it are ok
I changed transferbelt but the same.
please helppppp

[teckat]

Re: canon ir adv c7065 doubles photos with color

thanks very much but i see all drum and it are ok
I changed transferbelt but the same.
please helppppp

================================================== =========

================================================== =========

you get a PG 10 like that & receive no error code


1) Load 10 or more sheets of A4 (LTR) plain paper into the cassette 1.
2) In Service Mode > Mode List > COPIER > Option > FNC-SW > INTROT-T > Change the value to
"0". (Default value: 1, Range of setting: 0 to 3)
3) In Service Mode > Mode List > COPIER > TEST > PG > PG-PICK, and enter "1" to press "OK."
4) In Service Mode > Mode List > COPIER > TEST > PG > PG-QTY, and enter "5" to press "OK."
5) In Service Mode > Mode List > COPIER > TEST > PG > TYPE, and enter "32" to press "OK."
6) Press "Start" on the control panel, and check that the color displacement has been improved on the first to
4th sheets of output samples.
[Caution]
- When the other colors are displaced toward the rear side more than Bk is[a], go to step 7).
- When the other colors are displaced toward the front side more than Bk is[b], then check other factors as
this measure will not work.
[1] indicates paper feed direction.

Color Test.jpg
7) In Service Mode > Mode List > COPIER > Option > FNC-SW > INTROT-T, and enter any of "1" to "3" on
the basis of the sift length of the each color. (Default value: 1, Range of setting: 0 to 3)
Color Test.jpg
8) In Service Mode > Mode List > COPIER > Function > INSTALL > "INIT-ITB," and adjust the ITB neutral position.
9) Settings/Registration > Adjustment/Maintenance > Adjust Image Quality > Auto Correct Color Mismatch > press "Start."
Color Test.jpg
10) In Service Mode > Mode List > COPIER > TEST > PG > TYPE, and enter "6" to press "OK."
[Reference] Color displacement in the horizontal/ vertical directions can be checked by outputting the PG.
11) Press "Start" on Control Panel and check if color displacement has improved on 5 printed samples. If the symptom has improved, the work is completed.
[Reference] If the above remedy does not improve the color displacement, refer to the following FAQ.
- If fixed displacement in any color of YMCK occurs on all pages, refer to "Fixed displacement in any color of YMCK occurs on all pages".
- If fixed displacement in Bk occurs in a large quantity of print job, refer to "Fixed displacement in Bk occurs in a large quantity of print job".
- If large color displacement suddenly occurs in the horizontal scanning direction, refer to "Large color displacement suddenly occurs in the horizontal scanning direction."
- If fluctuating displacement in any color of YMC occurs in the vertical scanning direction, "Fluctuating displacement in any color of YMC occurs in the vertical scanning direction."
- If fluctuating displacement in Bk occurs in the vertical scanning direction, refer to "Fluctuating displacement in Bk occurs in the vertical scanning direction".
- If large displacement suddenly occurs in the vertical scanning direction, refer to "Large color displacement suddenly occurs in the vertical scanning direction."

SEE PDF for further checks > Fixed displacement/Large color displacement/Fluctuating displacement /etc.

[markndreu]

Re: canon ir adv c7065 doubles photos with color

Thank you for everything, but i haven't solved it yet. I have take the drums plus developers plus transferbelt, 4 lasers i have put the dates of lasers by another machine and i have put at this one, but the same thing. Please helpppppppp

[teckat]

Re: canon ir adv c7065 doubles photos with color

Thank you for everything, but i haven't solved it yet. I have take the drums plus developers plus transferbelt, 4 lasers i have put the dates of lasers by another machine and i have put at this one, but the same thing. Please helpppppppp

u have moved all those units to another c7065 and that printer has the same exact issue

LASERS are Probably the issue

remove the lasers / put in that printers lasers ---test