Bizhub 600 - jamming in the vertical conv. Tray 1

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • JOEBOOROCKSYOU
    Technician

    50+ Posts
    • Jan 2008
    • 85
    #1

    Bizhub 600 - jamming in the vertical conv. Tray 1

    well i have a good one for you all,
    i was just went on a service call on one of my bizhub 600s for jamming (from a cold start only) out of tray 1 going about 2/3 into the vertical conv.
    after you clear the jam it resumes the job and finishes just fine..no matter how many copies you select it will always stop right there on the first one
    and continue, finish the job just fine after you clear the jam..

    i'm fried on this one... and yes i replace the vertical unit with another one just to be safe..


    any ideas.....
    Tags: None
    • Cookr
      Trusted Tech

      Site Contributor
      100+ Posts
      • Dec 2011
      • 184
      #2
      Re: Bizhub 600 - jamming in the vertical conv. Tray 1

      Is it only tray 1 or does it happen with other trays also? So if you were to run 100 copies it would jam on first one then clear jam then it runs just fine after?

        Comment

        • JOEBOOROCKSYOU
          Technician

          50+ Posts
          • Jan 2008
          • 85
          #3
          Re: Bizhub 600 - jamming in the vertical conv. Tray 1

          Originally posted by Cookr
          Is it only tray 1 or does it happen with other trays also? So if you were to run 100 copies it would jam on first one then clear jam then it runs just fine after?
          yea only tray 1 , tray 2 works fine..

          and yes it doesn't matter if i run 5 copies or 100 , the first one from a cold start always jams right when entering the vertical conv., i clear it and it restarts the job and finishes beautiful..

          weirdest problem i have ever encountered in my 20 yrs of being a tec. logically it makes no sense....

            Comment

            • mx6turbo89
              Trusted Tech

              Site Contributor
              100+ Posts
              • Oct 2013
              • 154
              #4
              Re: Bizhub 600 - jamming in the vertical conv. Tray 1

              What jam code is showing up in the history?

                Comment

                • Brett GS
                  Trusted Tech

                  100+ Posts
                  • Jun 2013
                  • 154
                  #5
                  Re: Bizhub 600 - jamming in the vertical conv. Tray 1

                  Check the clutches that drive the vertical convyance and the clutch that drives the horizontal convyance tray above tray 2.

                    Comment

                    • MVPunisher
                      Trusted Tech

                      Site Contributor
                      100+ Posts
                      • May 2013
                      • 209
                      #6
                      Re: Bizhub 600 - jamming in the vertical conv. Tray 1

                      Tray 1 has a handful of ridiculous issues on this model. Easiest solution is to just set DIPsw 18-0 to 1 and tray 1 will never jam. ;-)

                        Comment

                        • allan
                          RTFM!!

                          5,000+ Posts
                          • Apr 2010
                          • 5462
                          #7
                          Re: Bizhub 600 - jamming in the vertical conv. Tray 1

                          Originally posted by MVPunisher
                          Tray 1 has a handful of ridiculous issues on this model. Easiest solution is to just set DIPsw 18-0 to 1 and tray 1 will never jam. ;-)
                          Jip very true.
                          Whatever

                            Comment

                            Previous template Next
                            Working...