C5501 - Turns off after printjob

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • mrwho
    Major Asshole!

    Site Contributor
    2,500+ Posts
    • Apr 2009
    • 4305
    #1

    [Electrical] C5501 - Turns off after printjob

    Hello there, guys and girls!

    Brand new C5501, just finished installing it. When taking out first test page, showed "Close Finisher Door" on the screen and then turned itself off. I disconnected the finisher to see if it was related, but it now just turns off at the end of a printjob without showing the message.

    I'm just short of installing the firmware, but if there are any tips, send them this way.

    Don't know if it is related, but I also noticed the power light at the right of the TFT doesn't turn on.

    Cheers!
    ' "But the salesman said . . ." The salesman's an asshole!'
    Mascan42

    'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'
    Ibid

    I'm just an ex-tech lurking around and spreading disinformation!
    Tags: c550, finisher, firmware, inserted, installing, job, light, mrwho, power, screen, send, test
    • mrwho
      Major Asshole!

      Site Contributor
      2,500+ Posts
      • Apr 2009
      • 4305
      #2
      Found it.

      First of all, the power light wasn't turning on because the LCD connector was not fully inserted.

      Second, the "turns off after a printjob" was because the auto shut-off comes from the factory at 0 minutes.

      I didn't realise it sooner because, like the power light, the powersave light was also not turning on.

      The "close finisher door" message is still a mistery to me, though.

      Thanks for your time reading this.

      Cheers!
      ' "But the salesman said . . ." The salesman's an asshole!'
      Mascan42

      'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'
      Ibid

      I'm just an ex-tech lurking around and spreading disinformation!

        Comment

        • Cantechman
          Trusted Tech

          Site Contributor
          100+ Posts
          • Nov 2008
          • 226
          #3
          Good job....

            Comment

            • Mr Spock
              Vulcan Inventor of Death

              1,000+ Posts
              • Aug 2006
              • 2064
              #4
              I believe some of the finishers are the same as the 1050 family and if so they need to be flashed to work with the 6500 family.
              And Star Trek was just a tv show...yeah right!

                Comment

                • Stirton.M
                  All things Konica Minolta

                  1,000+ Posts
                  • Oct 2009
                  • 1804
                  #5
                  Originally posted by Mr Spock
                  I believe some of the finishers are the same as the 1050 family and if so they need to be flashed to work with the 6500 family.
                  Yup.
                  "Many years ago I chased a woman for almost two years, only to discover that her tastes were exactly like mine: we both were crazy about girls."
                  ---Groucho Marx


                  Please do not PM me for questions related to Konica Minolta hardware.
                  I will not answer requests or questions there.
                  Please ask in the KM forum for the benefit of others to see the question and give their input.

                    Comment

                    • jma676
                      Expert Tech
                      250+ Posts
                      • Mar 2009
                      • 324
                      #6
                      Originally posted by mrwho
                      Found it.

                      First of all, the power light wasn't turning on because the LCD connector was not fully inserted.

                      Second, the "turns off after a printjob" was because the auto shut-off comes from the factory at 0 minutes.

                      I didn't realise it sooner because, like the power light, the powersave light was also not turning on.

                      The "close finisher door" message is still a mistery to me, though.

                      Thanks for your time reading this.

                      Cheers!

                      FS...? -- Beware!!!

                        Comment

                        • jma676
                          Expert Tech
                          250+ Posts
                          • Mar 2009
                          • 324
                          #7
                          Originally posted by Mr Spock
                          I believe some of the finishers are the same as the 1050 family and if so they need to be flashed to work with the 6500 family.
                          Be Careful!!!!

                          If this is the case (FS503), you need to configure, SW + CN jumper, and then Flash If it proved necessary.

                          Check the FS manual section.

                            Comment

                            Previous template Next
                            Working...