Warming Up,Ready To Scan in BIZHUB 750

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • trovico

    #1

    Warming Up,Ready To Scan in BIZHUB 750

    Warming up , Ready to scan message on bizhub-750 screen .
    i replace Drum,Developer & Toner control Sensor(in drum section) but Message still same.
    After 4-5 Hours rest machine again ready and working perfectly , but after one or two job message again appear and machine hanged on.
    today i also update new-firmware but still struck out in same condition .
    please help anybody for solution ..
  • minimerlin
    Senior Tech

    Site Contributor
    500+ Posts
    • Nov 2007
    • 851

    #2
    Re: Warming Up,Ready To Scan in BIZHUB 750

    Originally posted by trovico
    Warming up , Ready to scan message on bizhub-750 screen .
    i replace Drum,Developer & Toner control Sensor(in drum section) but Message still same.
    After 4-5 Hours rest machine again ready and working perfectly , but after one or two job message again appear and machine hanged on.
    today i also update new-firmware but still struck out in same condition .
    please help anybody for solution ..
    Fuser Lamps?
    Please do not PM me without asking first.

    Comment

    • trovico

      #3
      Re: Warming Up,Ready To Scan in BIZHUB 750

      Heater Lamps ON/OFF as per Schedule of system .

      Comment

      • minimerlin
        Senior Tech

        Site Contributor
        500+ Posts
        • Nov 2007
        • 851

        #4
        Re: Warming Up,Ready To Scan in BIZHUB 750

        Originally posted by trovico
        Heater Lamps ON/OFF as per Schedule of system .
        Have you checked the lamps are actually all working, maybe one is not, check not open circuit.
        Please do not PM me without asking first.

        Comment

        • DigiMan
          Trusted Tech

          Site Contributor
          250+ Posts
          • Jan 2013
          • 262

          #5
          Re: Warming Up,Ready To Scan in BIZHUB 750

          Since the lamps light is intense and since they are 2 right next to each other with naked eye its almost impossible to notice
          if one of them is not working,also maybe thermistor having glue-like dirt on it and not working correctly?
          I don't like the new copier I just bought. It says "put face down" but every time I do it, it blinds my eyes.

          Comment

          • JustManuals
            Field Supervisor

            5,000+ Posts
            • Jan 2006
            • 9919

            #6
            Re: Warming Up,Ready To Scan in BIZHUB 750

            This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from:


            Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


            Paul@justmanuals.com

            Comment

            • kronical
              Kronic Copier Ninja

              100+ Posts
              • Nov 2009
              • 230

              #7
              See this kind of thing all the time. Make sure you have toner in the machine. Warming Up is a generic 'please wait' message and also appears when adding toner. Even though it is not specifically calling for toner, check it and also check to make sure bottle is turning (may need to run toner replenish manually)

              If I had a dollar for every time i've seen this I would be retired now.

              Comment

              • chand226
                Technician
                • May 2013
                • 38

                #8
                Re: Warming Up,Ready To Scan in BIZHUB 750

                Originally posted by trovico
                Warming up , Ready to scan message on bizhub-750 screen .
                i replace Drum,Developer & Toner control Sensor(in drum section) but Message still same.
                After 4-5 Hours rest machine again ready and working perfectly , but after one or two job message again appear and machine hanged on.
                today i also update new-firmware but still struck out in same condition .
                please help anybody for solution ..

                no need of to change any firmware and drum.

                i have 200% correct formula for this copier (biz600/750/ di7210/7272). no toner on corona, no warming up, pleasewait.
                contact me at chand226@gmail.com

                Comment

                Working...