FS-4300DN 0501 jam

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nathansipe
    just another tech

    100+ Posts
    • Aug 2009
    • 122

    #1

    [Jamming] FS-4300DN 0501 jam

    Best rule for troubleshooting.
    K I S S Keep It Simple Stupid
  • nathansipe
    just another tech

    100+ Posts
    • Aug 2009
    • 122

    #2
    Re: FS-4300DN 0501 jam

    BTW, the printer has 270,000 prints on it and a recently installed fuser because of the roller staining recall issues.
    Best rule for troubleshooting.
    K I S S Keep It Simple Stupid

    Comment

    • leroyal
      Expert on The Obsolete
      100+ Posts
      • Sep 2007
      • 156

      #3
      Re: FS-4300DN 0501 jam

      Originally posted by nathansipe
      BTW, the printer has 270,000 prints on it and a recently installed fuser because of the roller staining recall issues.
      Check the tip of the fuser exit switch. Lots of broken ones out there.
      I know what I know better than anyone else knows what I know.

      Comment

      • Kyo fan
        Trusted Tech

        250+ Posts
        • Dec 2013
        • 368

        #4
        Re: FS-4300DN 0501 jam

        http://www.copytechnet.com/forums/ky...ange-jams.html

        Summary: Replace 3 paper feed pulleys and check if the spring under the paper feed assy is missing.

        Comment

        • nathansipe
          just another tech

          100+ Posts
          • Aug 2009
          • 122

          #5
          Re: FS-4300DN 0501 jam

          Thank you Kyo Fan. I can't believe it. I've been racking my brain, thinking that it had to be something simple. That link was exactly it. I checked and there is no spring.

          The good thing is I've learned a ton about this printer and how it assembles. Thanks again.
          Best rule for troubleshooting.
          K I S S Keep It Simple Stupid

          Comment

          • Kyo fan
            Trusted Tech

            250+ Posts
            • Dec 2013
            • 368

            #6
            Re: FS-4300DN 0501 jam

            You're welcome m8, this website is the best troubleshooting tool, just after service manual.

            Comment

            • andflop
              Junior Member
              • Jul 2012
              • 1

              #7
              Re: FS-4300DN 0501 jam

              I was wondering if you had any tips on how to remove the tray 1 lift motor

              Comment

              • B0265
                Senior Tech

                500+ Posts
                • Jan 2007
                • 718

                #8
                Re: FS-4300DN 0501 jam

                Originally posted by andflop
                I was wondering if you had any tips on how to remove the tray 1 lift motor
                There is a bulletin (2LV-0032 in Europe) about replacing some cluthes. In the part that describes how to replace the duplex clutch it is shown how remove the "cassette right guide", the lift motor is mounted in this unit.

                Note
                There is another bulletin (2LV-0043) that mentiones a broken shaft in this cassette right guide, perhaps you need to replace this part rather than the lift motor.

                Comment

                • ramaboss

                  #9
                  Re: FS-4300DN 0501 jam

                  Originally posted by Kyo fan
                  http://www.copytechnet.com/forums/ky...ange-jams.html

                  Summary: Replace 3 paper feed pulleys and check if the spring under the paper feed assy is missing.
                  thank you! you have very much helped me, i have had the same problem as at nathansipe. All problem was in a spring

                  Comment

                  • Geo
                    Senior Tech

                    500+ Posts
                    • Nov 2010
                    • 662

                    #10
                    Re: FS-4300DN 0501 jam

                    Originally posted by nathansipe
                    Thank you Kyo Fan. I can't believe it. I've been racking my brain, thinking that it had to be something simple. That link was exactly it. I checked and there is no spring.

                    The good thing is I've learned a ton about this printer and how it assembles. Thanks again.
                    Don't you just hate it when it's something this simple...Fortunately or unfortunately we have all been there....

                    P.S. That missing spring can also produce paper multi-feeds..

                    Cheers.

                    Comment

                    Working...