[Error Code] MPC4504 SC899 then SC991 then SC997

[wayniezaza]

Hi Guys

Getting a strange fault
Customer keeps getting SC899 but then it is followed by a SC991 and then a SC997.

All the latest firmware has been stuck on including the latest cheetah panel and Java.

Another strange thing is that although it sometimes happens in the afternoon it also happens at 1am , 4am , 9pm - Almost as if it is just sitting there and error codes.

The machine also has safecom on

Any suggestions?

[Choro1dal]

Re: MPC4504 SC899 then SC991 then SC997

Are the Heap and Stack sizes correctly set? The values should be in the SDK (Safecom) manual. If not, set both to no more than 75% of the maximum value displayed on screen.
User Tools, Machine Features, Extended Features, Extended Features, Admin Tools.

Check/ set the diprint timeout to at leat 60 seconds. By default this is 15 seconds.

[wayniezaza]

Re: MPC4504 SC899 then SC991 then SC997

Thanks for replying Choro1dal

Heaps and stacks are the same as the other 6 machines on site.

I have changed the Diprint settings. Will see how it goes and let you know

Thanks

[TonerMunkeh]

Re: MPC4504 SC899 then SC991 then SC997

But what are they set to?

[zed255]

Re: MPC4504 SC899 then SC991 then SC997

I had a machine behaving similarly and ended up going through a reset procedure (from the TSRC in the US) for the Java platform. This applies to machines where Java is on flash memory and not an SD card.

User Tools> System Settings> Admin Tools> Enhanced Authentication Management> OFF
Stop all applications, including Java
Disable Java in SP mode SP5-730-001 to 0
Format HDD 'Data for design and printer fonts' SP5-832-009 (usually, verify in manual for your specific model)
Perform SCS memory clear SP5-801-3
Return all SPs from SP5-401-160 to SP5-401-230 to default setting
Power Cycle
Enable Java in SP mode SP5-730-001 to 1
Power Cycle
Install Java from SD card
Reinstall applications.

[wayniezaza]

Re: MPC4504 SC899 then SC991 then SC997

Hi TonerMunkeh

The Heap Size was - 32Mb and the stack size was 512KB

Thanks Zed, i am going back to the customer on Monday to see if the machine has gone into an error state over the weekend, I was also thinking along the lines of something to do with Java, will give this a go and get back to you next week

[TonerMunkeh]

Re: MPC4504 SC899 then SC991 then SC997

Stack is set too high, I just had a 3503 with SC997 and setting the stack to 384 sorted it.

[Nasim]

Re: MPC4504 SC899 then SC991 then SC997

Hi,

some thing new about this case?

I have same problem on MPC4504SP with safecom.

[rsyarcia]

Re: MPC4504 SC899 then SC991 then SC997

with mp c2504exsp, we downgraded the java version. it was ok after...

[PJB]

Re: MPC4504 SC899 then SC991 then SC997

All -04 Machines with Safe Com has to have Java 12.45 or lower to work. Anything higher will cause problem

[jamie@ricohids.co.nz]

Re: MPC4504 SC899 then SC991 then SC997

Thanks Guys. Increased Heap Stack and it resolved my 991 &bunch of HDD errors. (Note-HDD was replaced a day ago for not being able to recover)

[Phil B.]

Re: MPC4504 SC899 then SC991 then SC997

Thanks Guys. Increased Heap Stack and it resolved my 991 &bunch of HDD errors. (Note-HDD was replaced a day ago for not being able to recover)

glad you found an answer .. but LEAVE threads over 2yrs old ALONE..

we call that GRAVE ROBBING.. bad bad boi