Ricoh Pro C5100S Driver

[Don3bdallah]

Please i need any driver helps me to print in banner mode
PCL6 driver only allows me to print in 487mm maximum
Not showing 120CM while the printer shows it

[slimslob]

Re: Ricoh Pro C5100S Driver

All drivers except XPS support banner printing.

487.7mm is larger than 120mm.

It will require a Custom paper size be set. You will have to set the Custom Size.

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

All drivers except XPS support banner printing.

487.7mm is larger than 120mm.

It will require a Custom paper size be set. You will have to set the Custom Size.

Sorry i mean 120CM

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

my machine and driver setting
bypass.jpg

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

It's exactly what the Specifications Data Sheet says. The machine does not support larger paper.

[ATTACH=CONFIG]45408[/ATTACH]

For banner printing you have to glue the printed sheets together.

bypass.jpg
no sir the machine suppoert banner mode up to 1260mm

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

Maybe it was changed with newer Firmware. Try to use the PRO C5200S PCL 6 Driver, it supports paper sizes up to 1260mm. Normaly it's not a problem to use older Ricoh machines with newer drivers or vice versa.

unfortunately nothing works
all drivers even the latest updated drivers stucked on 487mm

[slimslob]

Re: Ricoh Pro C5100S Driver

terramobil is correct. I just downloaded and installed the C5200 driver as well. You will have to use the bypass tray as the specs for the C5100 have to do with the the paper tray sizes. You will have to set up some means of properly supporting the banner as it is fed to keep it going straight and may not be able too stack multiple sheets.

If you plan to be printing a lot of banners, I would advise you get a wide format designed to actually do banners.

[mga]

Re: Ricoh Pro C5100S Driver

my machine and driver setting
[ATTACH=CONFIG]45407[/ATTACH]

Try using correct driver not universal and oem {ricoh}

[slimslob]

Re: Ricoh Pro C5100S Driver

Try using correct driver not universal and oem {ricoh}

His image was so fuzzy that I didn't even notice that.

Universal print drivers were created for one reason only. Pooled printers when those printers are not all exactly the same make and model. In order for printer pooling to work, all printers in the pool MUST BE USING THE SAME DRIVER.

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

Nothing works PCL6 Drivers , Universl Drivers , C5200 Drivers even different version of windows 7&10
anybody have any idea what is the problem

[Phil B.]

Re: Ricoh Pro C5100S Driver

Nothing works PCL6 Drivers , Universl Drivers , C5200 Drivers even different version of windows 7&10
anybody have any idea what is the problem

sounds like it might be time to call in a certified trained Ricoh tech

[slimslob]

Re: Ricoh Pro C5100S Driver

Sounds like you either did not download the proper Pro C5200 PCL6 driver or you are not using the bypass tray. Here is a link to the proper download page. The PCL6 driver that is listed first is the one to use.

Pro C5200S/C5210S Downloads | Ricoh Global

[Don3bdallah]

Re: Ricoh Pro C5100S Driver

Sounds like you either did not download the proper Pro C5200 PCL6 driver or you are not using the bypass tray. Here is a link to the proper download page. The PCL6 driver that is listed first is the one to use.

Pro C5200S/C5210S Downloads | Ricoh Global

i tried all nothing works

[farhad]

Re: Ricoh Pro C5100S Driver

hi
1.you just can print on 1200 cm when you use the machine by fiery
2.you can you this size just on bypass
3.you can use this size print on your bypass and USB flash by you displays right side

[zoor]

Re: Ricoh Pro C5100S Driver

GW Controller does not support banner printing. Only Controllers: E-22B/E-42B ( TSB 026 )

Bypass Length setting ( SP 5150 ) to " 1 " . Normally the paper length for sub scanning paper from the by-pass tray is limited to 600 mm, but this can be extended with this SP to 1260 mm.

1. Set t he SP5-150-001(01)
2. Change the "Bypass Tray Priority" setting of Fiery controller (E-22B/E-42B) to "Panel Setting".
3. While the Fiery controller is powered on and connected to the print engine, from the Operation Panel of print engine, register the (printer) tray paper settings: Bypass Tray.
4. In the printer driver, select "Bypass Tray" as input tray, and specify the paper size (Custom...):

Banner papers cannot be registered as custom paper.

Please i need any driver helps me to print in banner mode
PCL6 driver only allows me to print in 487mm maximum
Not showing 120CM while the printer shows it