1035

[hodgiepodgie]

installed fax board on 1035 wont show on op panel . does the printer card have to be specific to a 1035 mine says 1045 printer card thnk thats why machine (1035) does not see it. meaning fax board does not show nor printer on op panel.

[schooltech]

The DIMMS, if I remember, go in specific slots. Also, do you have the extra memory? Ricoh boxes like to have extra memory, some machine 64 MB, some up to 256 MB of memory to make the accessories be "seen" on the machine.

[hodgiepodgie]

ok

slot #1 according to manual but not sure on printer/scanner board mine says 1045 does that matter? have 1035.also tried w/64 and 256 mem

[hodgiepodgie]

ok

so i need a 1035 printer dimm for a 1035 copier.

[mikadonovan]

It is the same for a 1035 and 1045. This notepad document may help some.

[cobiray]

Memory (SDRAM)
32 MB (standard)
96 MB (maximum)
Note: There is 1 slot for a 64 MB DIMM.

[cobiray]

Same EDP code for 1035/1045 print options. Here's the install instructions.

1. Remove the left rear cover [A] (2 screws) and slide out the controller board [B]
(2 screws).
2. Install the printer ROM DIMM [C] on the controller board.
3. Remove the parallel interface cover [D].
4. This step is required only in the USA models.
Attach the FCC label [E] on the controller panel board aligned with the slot [F]
so the label is hidden when the left rear cover is replaced.
NOTE: If the NIB (G574), Postscript kit (G577), memory board (G578/G579), or
IEEE1394 Interface (G590) are to be installed, remove the HDD and install
them before proceeding to the next step.
5. Put back the controller board and replace the left rear cover.
6. Remove the connector cover [A] and lower rear cover [B] (5 screws).
7. Pull out the two paper trays [C].
8. Install edge clamp [D] in the opening.
9. Connect the four paper height sensors [E] to the cable [F].
10. Install the four paper height sensors [E] as shown.
11. Install the four cable clamps [G], then clamp the cable as shown.
12. Lead the cable through the opening [H]. Secure the cable in place with the
edge clamp attached in step 8.
13. Connect the cable to CN234 on the PCB [I].
14. Install the paper height sensor feeler [A] on the bottom plate shaft [B] of each
paper tray.
15. Reassemble the machine.
Paper Limit Sensor Installation
If the optional bridge unit has been installed, skip steps 16 and 17.
16. Peel off the black tape [C] from the anti-static brush [D], then pull out the cable
[E].
17. Connect the cable to the sensor [F], then install the paper limit sensor unit [G]
(2 screws).
Perform steps 18 to 20 only if the optional bridge unit has been installed.
If it has not been installed, go on to step 21.
18. Remove the connector cover [A] and bridge unit [B] (2 screws, 2 connectors).
19. Open the right cover [C] of the bridge unit and peel off the black tape [D], then
pull out the connector [E].
20. Install the paper sensor [F] (1 screw, 1 connector) and reinstall the bridge unit.
Completion
21. Remove the bottom cap [G] of the operation panel. Install the Printer key [H]
on the operation panel as shown.

[hodgiepodgie]

ok

thnks have manual but not clear on print dimm is it specific for 1035

[ccchuah]

In order for the fax to work, you must install fax board which is parallel to the controller board, NCU board for you to connect to telephone line, On the controller board, install a printer dimm on slot 1, 64mb PC100 SDRAM to the centre sodimm slot, install a network board for network printing. The printer board are same to 1045.

[imthinman]

1045

Could be two seperate issues, 1st the print is your NIC card enabled in service mode. Go to IEEE settings and check especially if you have done a RAM clear. 2ns issue is the Fax the correct one the 1045E model won't work

[hodgiepodgie]

ok maybe thats it possible 1045e