Firmware update error E32

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • [Horus
    Technician
    • Nov 2009
    • 17
    #1

    Firmware update error E32

    Hi,

    I'm was updating engine firmware on MPC1500SP, and stop the update. after 10 minutes i restart the machine.
    After that, always that i start the machine apear a error E32, reboot after card insert.

    I do that, but apear the same message.

    Some can help me.

    Thatnk's

    JM
    Tags: error, firmware, firmware update, interrupt, message, mpc, mpc1500sp, occur, stop, symptom, update, updating
    • zed255
      How'd ya manage that?

      1,000+ Posts
      • Dec 2009
      • 1024
      #2
      Never interrupt an update! Especially true for engine, system and network, but really applies to all modules. I doubt it but you can check to see if a 'boot card' exists for that model (they usually only do boot cards for larger machines). Check in the service manual to see if a firmware recovery procedure is outlined, if not you are likely on the market for boards. IIRC the BICU for engine and controller for the rest.

        Comment

        • [Horus
          Technician
          • Nov 2009
          • 17
          #3
          Hi,

          What is IIRC???,
          I only need the BICU (PCB BCU)????? to resolve this??

          Thank's

            Comment

            • zed255
              How'd ya manage that?

              1,000+ Posts
              • Dec 2009
              • 1024
              #4
              Originally posted by [Horus
              Hi,

              What is IIRC???,
              I only need the BICU (PCB BCU)????? to resolve this??

              Thank's
              IIRC=If I Recall Correctly

              Assuming the engine firmware is the only damaged one you may only require the BICU, consult the service manual as it should have some information on that specific models firmware structure.

                Comment

                • JustManuals
                  Field Supervisor

                  5,000+ Posts
                  • Jan 2006
                  • 9838
                  #5
                  This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from
                  Just Manuals | The Internet's largest selection of manuals | Instant Downloads


                  Paul@justmanuals.com

                    Comment

                    • teebee1234
                      Service Manager

                      Site Contributor
                      1,000+ Posts
                      • Jul 2008
                      • 1670
                      #6
                      This may or may not work on this model (this was for the 2105)....
                      ---------------------------------------------
                      [Symptom]
                      The "E32" and "E44" error codes are displayed.
                      When several softwares are installed in a same time, the "E32" and "E44" error codes may be displayed which will not turn off even if the SD card is removed and the power is turned off and on, and the system will not be ready for use.
                      [Cause]
                      A firmware transmission error may occur when installing several types of firmware simultaneously. Since the error data is saved to the NVRAM, the machine is unable to boot up normally, even after the main switch is turned Off/On.

                      How to cancel the errors:
                      1) Press "143" using the number keys while the error code is displayed.
                      2) Press the "CLEAR" key 3 times.
                      3) The system will beep 3 times and the error display will disappear.
                      To ensure the above error codes do not occur, please be sure to follow the procedure below whenever installing several kinds of firmware at the same time: 1. First, install the System firmware only. 2. After successfully installing the System firmware, turn the machine main power Off/On and confirm that the machine boots up to Ready status normally. 3. Install the remaining firmware simultaneously. Note: Refer RTB RB070040 as to details.

                        Comment

                        Previous template Next
                        Working...