Problem with MP9000. Please urgent help

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Masterchief
    replied
    Re: Problem with MP9000. Please urgent help

    Make sue you have assessed the WEB condition and if needed that you have replaced it CORRECTLY, i know these fusers have the old 1060/1075 parts so im concerned as to the state of the termostats also

    Let me know

    Masterchef

    Leave a comment:


  • Moza
    replied
    Format HDD sp-5832 should do the trick

    Leave a comment:


  • Avago
    Guest replied
    Re: Problem with MP9000. Please urgent help

    Originally posted by idplus2
    Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?
    I've had this one before on another model (mp5500 I think), you've told the machine there's a brand new web but in fact you've taken one from another machine which has probably used up some of the web already. the reading back from the arm sensor which sits on the web doesn't match what the machine expects and it throws the machine into a loop.
    The old fusing web might not sort this out as the values are all over the place.

    You need to put in a brand new web and the zero value you've entered will match the reading from the sensor. hope this helps

    Leave a comment:


  • certifiedxeroxtech
    replied
    Re: Problem with MP9000. Please urgent help

    align the web padre or check the whole fusing unit.

    Leave a comment:


  • totoro
    replied
    Re: Problem with MP9000. Please urgent help

    Put the original fuser back in the machine and see what changes.

    Leave a comment:


  • sharpmind
    replied
    Re: Problem with MP9000. Please urgent help

    First, disconnect the HDD to check whether "Please Wait" still appears.If same problem, try to clean the drum potential sensor.That is my basic idea.

    Leave a comment:


  • idplus2
    replied
    Re: Problem with MP9000. Please urgent help

    Originally posted by rajmalini
    pls cold reset your printer.
    Thank you for your help but what do you mean by " Cold reset"?

    Leave a comment:


  • idplus2
    replied
    Re: Problem with MP9000. Please urgent help

    Originally posted by Bantams
    Did you actually replace the Web

    i replaced it by a fuser from another MP9000. Do i have to replace the web entirely from the one replaced?

    Leave a comment:


  • Bantams
    replied
    Re: Problem with MP9000. Please urgent help

    Did you actually replace the Web

    Leave a comment:


  • fbkhan3
    replied
    Re: Problem with MP9000. Please urgent help

    Originally posted by idplus2
    Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?
    What else did you do with fuser? look for trap wire,bad Thermistor, Open Thermofuse or make sure Fuser is properly seated and connected to female connector in the rear,

    good luck!

    Leave a comment:


  • JustManuals
    replied
    Re: Problem with MP9000. Please urgent help

    This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from


    Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


    Paul@justmanuals.com

    Leave a comment:


  • idplus2
    replied
    Re: Problem with MP9000. Please urgent help

    Thank you for your help but what do you mean by " Cold reset"?

    Leave a comment:


  • rajmalini
    Guest replied
    Re: Problem with MP9000. Please urgent help

    Originally posted by idplus2
    Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?

    pls cold reset your printer.

    Leave a comment:


  • idplus2
    started a topic Problem with MP9000. Please urgent help

    Problem with MP9000. Please urgent help

    Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?
Working...