Enter SP Mode on Ricoh 1107ex

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • D_Ritter
    Technician
    • May 2010
    • 16

    #1

    Enter SP Mode on Ricoh 1107ex

    Hello everybody,

    I need to reset the PM counter of the fusing unit on a 1107ex, but in the service-manual I can't find how to enter the SP Mode. Also googled and searched the Forum without succes. Isn't it "C"-1-0-7-"Stopp"?

    Thanks for your support and have a nice day!
  • totoro
    Senior Tech

    Site Contributor
    500+ Posts
    • Apr 2008
    • 568

    #2
    Re: Enter SP Mode on Ricoh 1107ex

    press "yellow clear modes\reset" , 1, 0, 7, hold "C"
    Totoro

    Comment

    • slimslob
      Retired

      Site Contributor
      25,000+ Posts
      • May 2013
      • 37503

      #3
      Re: Enter SP Mode on Ricoh 1107ex

      Most of the newer models have a red "Stop" button and a grey or blue "Clear" button. "C" is the "Clear" button.

      Comment

      • D_Ritter
        Technician
        • May 2010
        • 16

        #4
        Re: Enter SP Mode on Ricoh 1107ex

        Thanks guys, it was the blue "C"-Button
        Now I set the PM-counter of fuser and fusercleaning 0, but message still shows up and blocks the machine. Will have a look into the SM tomorrow, maybe I did something wrong.

        Thanks again.

        Comment

        • slimslob
          Retired

          Site Contributor
          25,000+ Posts
          • May 2013
          • 37503

          #5
          Re: Enter SP Mode on Ricoh 1107ex

          Originally posted by D_Ritter
          Thanks guys, it was the blue "C"-Button
          Now I set the PM-counter of fuser and fusercleaning 0, but message still shows up and blocks the machine. Will have a look into the SM tomorrow, maybe I did something wrong.

          Thanks again.
          By set the PM counter to 0, did you use the on screen clear for each or did you change the target value to 0? The on screen Clear button for the fusing unit will clear its count to 0 and also all the component parts below it. If the cleaning web had completely ran out, you may need to set SP 1902-001 to 0. Some machine also require rebooting.

          Comment

          • lauram007

            #6
            Re: Enter SP Mode on Ricoh 1107ex

            Originally posted by slimslob
            By set the PM counter to 0, did you use the on screen clear for each or did you change the target value to 0? The on screen Clear button for the fusing unit will clear its count to 0 and also all the component parts below it. If the cleaning web had completely ran out, you may need to set SP 1902-001 to 0. Some machine also require rebooting.
            thanks for the information

            Comment

            • D_Ritter
              Technician
              • May 2010
              • 16

              #7
              Re: Enter SP Mode on Ricoh 1107ex

              Good morning Slimsob,

              I used the Clear Buttons, so I think it must be SP 1902-001. Tried everything yesterday, even set Fuser-PM to useraction instead of service, but nothing helped.
              I will visit the machine today and give it another try. Thank you for your help.

              Comment

              • willienelson
                Technician
                • Jul 2015
                • 11

                #8
                Re: Enter SP Mode on Ricoh 1107ex

                Very definitely sp1902 code needs resetting to zero.

                Assuming of course you fitted the web correctly and the sensor flag is not on the wrong side of the web!

                Comment

                • D_Ritter
                  Technician
                  • May 2010
                  • 16

                  #9
                  Re: Enter SP Mode on Ricoh 1107ex

                  Thanks to everybody. Set 1902 to 0 and everything worked fine.
                  Problem solved!

                  Comment

                  Working...