SCX 5935fn touch screen

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Copier Addict
    Aging Tech

    Site Contributor
    10,000+ Posts
    • Jul 2013
    • 14813
    #1

    SCX 5935fn touch screen

    Does anyone know if it is possible to calibrate the touch screen on these machines? I have one where the bottom half of the touch screen is lined up but the top half is close to an inch out of adjustment. I have upgraded firmware and re-formatted the hard drive. I didn't think formatting the HDD would help, but I figured "nothing ventured, nothing gained"
    Thanks for any help.
    Tags: None
    • arnh79
      Trusted Tech

      Site Contributor
      VIP Subscriber
      250+ Posts
      • Apr 2010
      • 468
      #2
      Re: SCX 5935fn touch screen

      Yes you can calibrate. Turn machine off, hold the 0 key down and turn machine back on. Keep holding 0 key down until a calibration screen appears. Follow instructions on the screen.
      Why does every customer think they're the first one to ever say: "you've been here so much we should get you an office, ha, ha, ha"?

        Comment

        • Copier Addict
          Aging Tech

          Site Contributor
          10,000+ Posts
          • Jul 2013
          • 14813
          #3
          Re: SCX 5935fn touch screen

          Originally posted by arnh79
          Yes you can calibrate. Turn machine off, hold the 0 key down and turn machine back on. Keep holding 0 key down until a calibration screen appears. Follow instructions on the screen.
          Thanks arnh79, that did the trick. Much appreciated.

            Comment

            • toner cartridge
              Technician
              • Sep 2014
              • 33
              #4
              Re: SCX 5935fn touch screen

              Originally posted by copier addict
              Does anyone know if it is possible to calibrate the touch screen on these machines? I have one where the bottom half of the touch screen is lined up but the top half is close to an inch out of adjustment. I have upgraded firmware and re-formatted the hard drive. I didn't think formatting the HDD would help, but I figured "nothing ventured, nothing gained"
              Thanks for any help.




              hi friend, if calibrate failed, you can buy a good touch screen (compatible quality is not expensive) to replace, and work stable




              copier spare parts

                Comment

                • ZOOTECH
                  Senior member of CRS

                  Site Contributor
                  2,500+ Posts
                  • Jul 2007
                  • 3375
                  #5
                  Re: SCX 5935fn touch screen

                  Originally posted by arnh79
                  Yes you can calibrate. Turn machine off, hold the 0 key down and turn machine back on. Keep holding 0 key down until a calibration screen appears. Follow instructions on the screen.
                  Thanks arnh79 for this info; however, I get to the calibration screen, press the 9 crosses, and then it says "success, press any key to validate" - is there suppose to be another validation of success, or do we have to power off/on? The hit/miss of the touch screen was not helped by this procedure after powering off/on. After the "success,..." and pressing any key or cross on the display, nothing happens - I have to power off/on.
                  I may have to follow toner cartridge's advice.
                  "You can't trust your eyes, if your mind is out of focus" --

                    Comment

                    • arnh79
                      Trusted Tech

                      Site Contributor
                      VIP Subscriber
                      250+ Posts
                      • Apr 2010
                      • 468
                      #6
                      Re: SCX 5935fn touch screen

                      I think you have to do it twice in a row before you get the "please reboot" message. First time, hit all the cross marks then the message "success, press any key to validate", then message reappears to hit all the cross marks. Do it again and it will say reboot.
                      Why does every customer think they're the first one to ever say: "you've been here so much we should get you an office, ha, ha, ha"?

                        Comment

                        • ZOOTECH
                          Senior member of CRS

                          Site Contributor
                          2,500+ Posts
                          • Jul 2007
                          • 3375
                          #7
                          Re: SCX 5935fn touch screen

                          Originally posted by arnh79
                          I think you have to do it twice in a row before you get the "please reboot" message. First time, hit all the cross marks then the message "success, press any key to validate", then message reappears to hit all the cross marks. Do it again and it will say reboot.
                          Tks, I'll try that next.
                          "You can't trust your eyes, if your mind is out of focus" --

                            Comment

                            Previous template Next
                            Working...