MX2314 - please wait

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Leebs14
    Trusted Tech

    250+ Posts
    • Feb 2014
    • 457
    #1

    MX2314 - please wait

    I've read the posts on this error posted earlier in this forum but some relate to the 2614 and not the basic 2314. The ram is onboard and not a plug in dimm.

    My machine boots up fine, cleans the transfer belt message comes and goes then it calibrates itself all ok and then says please wait and just sits there. No restart or anything works, can't access system settings or service mode. You can ping it and get a reply but can't open machines webpage.

    Tried emergency firmware update which all went through fine but problem exactly the same?


    Sent from my iPhone using Tapatalk
    Tags: None
    • ZOOTECH
      Senior member of CRS

      Site Contributor
      2,500+ Posts
      • Jul 2007
      • 3375
      #2
      Re: MX2314 - please wait

      Originally posted by Leebs14
      I've read the posts on this error posted earlier in this forum but some relate to the 2614 and not the basic 2314. The ram is onboard and not a plug in dimm.

      My machine boots up fine, cleans the transfer belt message comes and goes then it calibrates itself all ok and then says please wait and just sits there. No restart or anything works, can't access system settings or service mode. You can ping it and get a reply but can't open machines webpage.

      Tried emergency firmware update which all went through fine but problem exactly the same?


      Sent from my iPhone using Tapatalk
      Unplug the network cable and see if it goes ready.
      "You can't trust your eyes, if your mind is out of focus" --

        Comment

        • Leebs14
          Trusted Tech

          250+ Posts
          • Feb 2014
          • 457
          #3
          Re: MX2314 - please wait

          No it doesn't. I unplugged it from the network and then did the firmware but it's exactly the same..


          Sent from my iPhone using Tapatalk

            Comment

            • ZOOTECH
              Senior member of CRS

              Site Contributor
              2,500+ Posts
              • Jul 2007
              • 3375
              #4
              Re: MX2314 - please wait

              Disable Warmup in TC 7-1 to see if it will go ready; also, disable Fusing and DV to see if it will go ready.
              Run TC 25-1 (with toners removed) and check for any levels that might be near over toned or under toned.
              "You can't trust your eyes, if your mind is out of focus" --

                Comment

                • Leebs14
                  Trusted Tech

                  250+ Posts
                  • Feb 2014
                  • 457
                  #5
                  Re: MX2314 - please wait

                  Thanks for your suggestions but the machine will not allow you into any modes at all to adjust or turn anything on or off. Even starting the machine with the door open it still won't accept p*c* code


                  Sent from my iPhone using Tapatalk

                    Comment

                    • Leebs14
                      Trusted Tech

                      250+ Posts
                      • Feb 2014
                      • 457
                      #6
                      Re: MX2314 - please wait

                      Update - been back today a replaced the SD card and it worked first time. So must have been corrupted data on the card,


                      Sent from my iPhone using Tapatalk

                        Comment

                        • michaelc
                          Field Tech

                          Site Contributor
                          500+ Posts
                          • Mar 2011
                          • 590
                          #7
                          Re: MX2314 - please wait

                          It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
                          It didn't say that I couldn't do it in the manual.

                            Comment

                            • daniele091
                              #8
                              Re: MX2314 - please wait

                              Originally posted by michaelc
                              It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
                              Hi dear,
                              you can send me a copy of your sd card?
                              I have a printer sharp mx2314, it has blocked the sd and I can not start it.


                              I'm waiting.
                              Thank you

                                Comment

                                • Jyothis
                                  Junior Member
                                  • Jun 2022
                                  • 1
                                  #9
                                  Re: MX2314 - please wait

                                  Originally posted by michaelc
                                  It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
                                  Can you pls share the sd card image for mx2314n

                                    Comment

                                    Previous template Next
                                    Working...