ar-p450 test comands

[DINGO]

Hi
can someone tell me how i can perform the s.m. comands in the ar-p450 ( without scanner, only print)
for execute the s.m 14, 15, clean the mainetence messages and so?
regards

[spotlifter]

Re: ar-p450 test comands

Power off the machine. Hold down the Menu and OK buttons. Power the machine on. Release the buttons after a few seconds. Press menu until you reach to whatever commands you want to do. Good luck.

[DINGO]

Re: ar-p450 test comands

Power off the machine. Hold down the Menu and OK buttons. Power the machine on. Release the buttons after a few seconds. Press menu until you reach to whatever commands you want to do. Good luck.

hi
i already have do that, but i can,t know i performe for exemple the sm 14?? and how i can reset the maintenance message, and so?

regards

[DAR]

Re: ar-p450 test comands

Go to Sharpnet and download the ARP350 manual.

[DINGO]

Re: ar-p450 test comands

Go to Sharpnet and download the ARP350 manual.

was a great idea, but unfortunaly i haven`t passwords for acess to sharpnet.

thanks anywai

[rainmaker]

Re: ar-p450 test comands

A. Entering the diag mode

With the power OFF, hold and press the [MENU] key and the [OK] key,and at the same time turn on the power.

B. Selecting diag menus

Press the [MENU] key to change the diag menu.Pressing OPERATION GUIDE key returns to the previous menu.Press the [OK] key to execute the test.Press [ ] or [ ] key to go to the input menu.Press the [BACK/C] key to return to the previous menu.

C. Canceling the diag mode

Turn off the power to cancel the diag mode. try this.......rainmaker

[DINGO]

Re: ar-p450 test comands

thanks, i am try get de service manual from the print version for understand the menus.

[rainmaker]

Re: ar-p450 test comands

display PCU DIAG MODE #Sensor check mode SENSOR CHECK XXLSU test LASER SYSTEM TESTLED/LCD test LED/LCD TESTHigh voltage test HV TEST XXXOperation test mode LOAD TEST XXAuto developer adjustment AUTOMATIC DV ADJ.Laser output setup LASER OUTPUT SETUP (XXX)Fusing temperature setup FUSER TEMP. SETTING XProcess control value setup SLOW UP SETTINGPaper feed size setup SIZE ADJUSTMENT XICU print mode setup ICU PRINT MODE SETTest print TEST PRINT XXWarm-up time display WARM UP TIME DISPLAYCounter display COUNTER DISPLAYCounter clear COUNTER CLEARTrouble cancel TROUBLE CANCEL XPaper feed tray size setup XXX SIZE SETUPDestination setup DESTINATION SETUPPaper feed tray paper type setup TRAY DETECT TYPE xxCE mark setup CE MARK SETTINGclear.

Used to clear each counter value.(LCD display)*Pressing the [ ] or [ ] key selects the counter group for the counter clear mode.*Pressing [OK] key displays the counter clear group.*Using [MENU] moves to the next mode*Pressing the [ ] or [ ] keys changes the YES or NO.*Pressing [OK] key starts the counter data clear mode.*Pressing [BACK/C] key terminates the counter data clear mode.COUNTER CLEAR:TROUBLE CANCEL X

Trouble cancel.

Used to cancel a trouble code.(LCD display)*Pressing the [ ] or [ ] key selects the trouble cancel mode.*Pressing [OK] key start the trouble cancel mode.*Using [ ] and [ ] keys changes the YES or NO.*Pressing [OK] key starts the trouble cancel mode.*Pressing [BACK/C] key terminates the trouble cancel mode.Menu ContentInitialvalueSetrange

XXXXX COUNTER CLEAR

FEED COUNTER CLEAR DEVE COUNTER CLEARTRAY1 Paper feed tray 1 counter DEVE Developing counterTRAY2 Paper feed tray 2 counter DRUM COUNTER CLEARLCC1/TRAY3 Paper feed tray 3 counter DRUM Drum counterLCC1/TRAY4 LCC1 or paper ray tray 4 counter TONER COUNTER CLEARBPT Manual paper feed counter TONER Toner counterADU Duplex counter OUTPUT COUNTER CLEARSTAPLE COUNTER CLEAR TOTAL OUTPUT Copy counter(Effective paper counter)STAPLE Staple counter PRINTER Printer counterPUNCH Punch counter OTHERS OthersMNT COUNTER CLEAR TIMER DATA CLEARMENTENANCE Maintenance counter DRUM ROTATION Drum motor RPMDEVE ROTATION Developing motor RPMJAM/TBL COUNTER CLJAM Jam counterTROUBLE Trouble counter

TROUBLE CANCEL X

X:

E-

A3 count mode setup COUNTUP MODE SETUP XMaintenance cycle setup MNT CYCLE SETUPOperation-at-life-over setup LIFE OVER SETTINGFinisher jogger adjustment FINISHER JOGGER ADJ.Console finisher setup CONSOLE FIN. SET XTrouble memory mode setup MEMORY MODE SETTINGLast JAM code display LAST JAM CODE DISPSystem information display SYSTEM INFORMATION X hope this helps......rainmakerProcess control data display PROCESS DATA DISP XPort check CENTRO PORT CHECK

SELECT IN signal setup SELECT IN SIGNAL SET

[DINGO]

Re: ar-p450 test comands

display PCU DIAG MODE #Sensor check mode SENSOR CHECK XXLSU test LASER SYSTEM TESTLED/LCD test LED/LCD TESTHigh voltage test HV TEST XXXOperation test mode LOAD TEST XXAuto developer adjustment AUTOMATIC DV ADJ.Laser output setup LASER OUTPUT SETUP (XXX)Fusing temperature setup FUSER TEMP. SETTING XProcess control value setup SLOW UP SETTINGPaper feed size setup SIZE ADJUSTMENT XICU print mode setup ICU PRINT MODE SETTest print TEST PRINT XXWarm-up time display WARM UP TIME DISPLAYCounter display COUNTER DISPLAYCounter clear COUNTER CLEARTrouble cancel TROUBLE CANCEL XPaper feed tray size setup XXX SIZE SETUPDestination setup DESTINATION SETUPPaper feed tray paper type setup TRAY DETECT TYPE xxCE mark setup CE MARK SETTINGclear.

Used to clear each counter value.(LCD display)*Pressing the [ ] or [ ] key selects the counter group for the counter clear mode.*Pressing [OK] key displays the counter clear group.*Using [MENU] moves to the next mode*Pressing the [ ] or [ ] keys changes the YES or NO.*Pressing [OK] key starts the counter data clear mode.*Pressing [BACK/C] key terminates the counter data clear mode.COUNTER CLEAR:TROUBLE CANCEL X

Trouble cancel.

Used to cancel a trouble code.(LCD display)*Pressing the [ ] or [ ] key selects the trouble cancel mode.*Pressing [OK] key start the trouble cancel mode.*Using [ ] and [ ] keys changes the YES or NO.*Pressing [OK] key starts the trouble cancel mode.*Pressing [BACK/C] key terminates the trouble cancel mode.Menu ContentInitialvalueSetrange

XXXXX COUNTER CLEAR

FEED COUNTER CLEAR DEVE COUNTER CLEARTRAY1 Paper feed tray 1 counter DEVE Developing counterTRAY2 Paper feed tray 2 counter DRUM COUNTER CLEARLCC1/TRAY3 Paper feed tray 3 counter DRUM Drum counterLCC1/TRAY4 LCC1 or paper ray tray 4 counter TONER COUNTER CLEARBPT Manual paper feed counter TONER Toner counterADU Duplex counter OUTPUT COUNTER CLEARSTAPLE COUNTER CLEAR TOTAL OUTPUT Copy counter(Effective paper counter)STAPLE Staple counter PRINTER Printer counterPUNCH Punch counter OTHERS OthersMNT COUNTER CLEAR TIMER DATA CLEARMENTENANCE Maintenance counter DRUM ROTATION Drum motor RPMDEVE ROTATION Developing motor RPMJAM/TBL COUNTER CLJAM Jam counterTROUBLE Trouble counter

TROUBLE CANCEL X

X:

E-

A3 count mode setup COUNTUP MODE SETUP XMaintenance cycle setup MNT CYCLE SETUPOperation-at-life-over setup LIFE OVER SETTINGFinisher jogger adjustment FINISHER JOGGER ADJ.Console finisher setup CONSOLE FIN. SET XTrouble memory mode setup MEMORY MODE SETTINGLast JAM code display LAST JAM CODE DISPSystem information display SYSTEM INFORMATION X hope this helps......rainmakerProcess control data display PROCESS DATA DISP XPort check CENTRO PORT CHECK

SELECT IN signal setup SELECT IN SIGNAL SET

Thanks friend, i already get the service manual.

regards

[DINGO]

Re: ar-p450 test comands

hi
with the service manual the work in this print was easy.

[rainmaker]

Re: ar-p450 test comands

good job...have a great one today......rainmaker