AR-M277 No power after dismantling the Delivery Frame

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Jose Mari S. De Leon
    Junior Member
    • Feb 2013
    • 6
    #1

    AR-M277 No power after dismantling the Delivery Frame

    Hi.. I need help about my Sharp Ar-M277, now not turning ON.

    All happens when I removed the Delivery Frame to fix the broken plastic parts and after assembling and put back together to its original position, when I try to power ON the machine I got no display from the LCD and the machine is not turning ON. Did I missed something here?

    Thank you...
    Tags: None
    • bilyahn
      Service Manager

      1,000+ Posts
      • Dec 2006
      • 1470
      #2
      Re: AR-M277 No power after dismantling the Delivery Frame

      Try reseating the connectors on the main board near the delivery units connector. Might just have pulled the ribbon cable loose as they are very near to each other. That would explain the display being dead.

      Good luck.

      Bil

        Comment

        • Jose Mari S. De Leon
          Junior Member
          • Feb 2013
          • 6
          #3
          Re: AR-M277 No power after dismantling the Delivery Frame

          Originally posted by bilyahn
          Try reseating the connectors on the main board near the delivery units connector. Might just have pulled the ribbon cable loose as they are very near to each other. That would explain the display being dead.

          Good luck.

          Bil
          Thanks Bill I will check again and will reseat all the cables. Will post here the result... Thanks again.

            Comment

            • Jose Mari S. De Leon
              Junior Member
              • Feb 2013
              • 6
              #4
              Re: AR-M277 No power after dismantling the Delivery Frame

              After trying to re-connect all the cables, the machine is now powering ON (Thanks Bil) but I got a "CALL FOR SERVICE. CODE F9-10". Is there a reset function to reset this error?

              Thanks...

                Comment

                • MHeon71
                  Trusted Tech

                  Site Contributor
                  250+ Posts
                  • Oct 2008
                  • 489
                  #5
                  Re: AR-M277 No power after dismantling the Delivery Frame

                  No, I do not think a TC will clear the code and I believe it would just reset after cycling the power. If you must try, try TC 14. The error code shows that it is a printer PWB trouble. I would try reseating the printer PWB and any memory associated with it.

                    Comment

                    • JustManuals
                      Field Supervisor

                      5,000+ Posts
                      • Jan 2006
                      • 9838
                      #6
                      Re: AR-M277 No power after dismantling the Delivery Frame

                      This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from:


                      http://www.justmanuals.com



                      Paul@justmanuals.com

                        Comment

                        • ZOOTECH
                          Senior member of CRS

                          Site Contributor
                          2,500+ Posts
                          • Jul 2007
                          • 3375
                          #7
                          Re: AR-M277 No power after dismantling the Delivery Frame

                          First off, update the firmware. With these machines, there are a lot of things that can cause these F9 codes. Take it down to basics, and test.
                          "You can't trust your eyes, if your mind is out of focus" --

                            Comment

                            • Jose Mari S. De Leon
                              Junior Member
                              • Feb 2013
                              • 6
                              #8
                              Re: AR-M277 No power after dismantling the Delivery Frame

                              Originally posted by MHeon71
                              No, I do not think a TC will clear the code and I believe it would just reset after cycling the power. If you must try, try TC 14. The error code shows that it is a printer PWB trouble. I would try reseating the printer PWB and any memory associated with it.
                              Thank you MHeon71, everything now is working properly, tried to reseat the memory and it works... More power to you all guys...

                                Comment

                                Previous template Next
                                Working...