Toshiba studio 650 wait after copy for 15 seconds

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ELIAS G
    Technician
    • Jun 2011
    • 14

    #1

    Toshiba studio 650 wait after copy for 15 seconds

    e studio 650 says wait after the end of copy for about 15 seconds (the machine is runing) and then goes to ready.
    I have change all the thermistors , toner motor and recycle motor are ok.
    Any ideas.
    Thanks
  • michaelc
    Field Tech

    Site Contributor
    500+ Posts
    • Mar 2011
    • 590

    #2
    Re: Toshiba studio 650 wait after copy for 15 seconds

    are you doing more than 1 copy while it does this?
    It didn't say that I couldn't do it in the manual.

    Comment

    • bojans
      Service Manager

      Site Contributor
      1,000+ Posts
      • Feb 2008
      • 1313

      #3
      Re: Toshiba studio 650 wait after copy for 15 seconds

      Try formatting HDD.

      Comment

      • ELIAS G
        Technician
        • Jun 2011
        • 14

        #4
        Re: Toshiba studio 650 wait after copy for 15 seconds

        GOOD MORRNING FROM ATHENS
        THANK YOU ALL
        MICHAELC : it does intependently of number of copy one or more,exactly at the end of procedure .
        BOJANS :format is ok but the problem stays.

        Comment

        • fourl6
          Technician

          50+ Posts
          • Nov 2008
          • 94

          #5
          Re: Toshiba studio 650 wait after copy for 15 seconds

          iv had wait issues caused but temperature/humidity sensors. no idea where they are on a 650 sorry.
          i'd also give the IH board a good clean.

          Cheers Cam

          Comment

          • esam ramadan
            Trusted Tech
            • Feb 2008
            • 199

            #6
            Re: Toshiba studio 650 wait after copy for 15 seconds

            set 08-803 to 2 if it not 2 it can make this problem

            Comment

            • michaelc
              Field Tech

              Site Contributor
              500+ Posts
              • Mar 2011
              • 590

              #7
              Re: Toshiba studio 650 wait after copy for 15 seconds

              I know on some other models thermistors can cause issues like this. Maybe worth giving them a clean (or replace if worn) and also the IH board like fourl6 suggested. Have you also checked your toner cartridge, toner unit and waste toner recycle unit. Also had a semi worn dev drive gear (the one on the back of the dev unit) give a similar issue before it failed. It used to go around the shaft 360 then sit back in position and drive for a bit.
              It didn't say that I couldn't do it in the manual.

              Comment

              • JustManuals
                Field Supervisor

                5,000+ Posts
                • Jan 2006
                • 9838

                #8
                Re: Toshiba studio 650 wait after copy for 15 seconds

                This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from

                Just Manuals ~ The Internet's largest selection of manuals ~ Instant Downloads


                Paul@justmanuals.com

                Comment

                • ELIAS G
                  Technician
                  • Jun 2011
                  • 14

                  #9
                  Re: Toshiba studio 650 wait after copy for 15 seconds

                  Good morning from athens to all
                  have a good week and a happy new year.
                  Many-many thanks to all for your help.
                  specially to esam ramadan . your help was the solution in this problem.thanks a lot
                  :d

                  Comment

                  • esam ramadan
                    Trusted Tech
                    • Feb 2008
                    • 199

                    #10
                    Re: Toshiba studio 650 wait after copy for 15 seconds

                    Originally posted by ELIAS G
                    Good morning from athens to all
                    have a good week and a happy new year.
                    Many-many thanks to all for your help.
                    specially to esam ramadan . your help was the solution in this problem.thanks a lot
                    :d
                    YOU ARE WELCOME

                    Comment

                    Working...