CB80 Error Code

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • toshibadale
    Trusted Tech

    100+ Posts
    • Apr 2007
    • 117
    #1

    [Error Code] CB80 Error Code

    I have a 855 with a MJ-1027 with a MJ-6003N hole punch attached. It is giving the CB-80 error code. I've replaced the whole unit...and both boards on the units, and tried the adjustments.

    It still keeps throwing the error. I've unplugged the hole punch so the customer can use the machine, but need to know if anyone has any ideas on how to get rid of this code!
    Tags: 1027, 600, adjustments, code, customer, error, hole, unit, units
    • Martini
      #2
      Re: CB80 Error Code

      First clean the two exit sensors before the stationary tray, then replace the puncher's EPROM, it's now available from Toshiba.

        Comment

        • canonbundy
          Senior Tech

          500+ Posts
          • Jun 2012
          • 607
          #3
          Re: CB80 Error Code

          Originally posted by toshibadale
          I have a 855 with a MJ-1027 with a MJ-6003N hole punch attached. It is giving the CB-80 error code. I've replaced the whole unit...and both boards on the units, and tried the adjustments.

          It still keeps throwing the error. I've unplugged the hole punch so the customer can use the machine, but need to know if anyone has any ideas on how to get rid of this code!
          Maybe update F/W with all units connected otherwise - below.

          [CB80] Backup RAM data abnormality[CB90] Paper pushing plate motor abnormality
          Is the problem solved by turning the power of the equipment OFF and ON?
          ��
          YES �� End.NOReplace the finisher controller PC board.
          Replace tha punch driver PC board.

            Comment

            • toshibadale
              Trusted Tech

              100+ Posts
              • Apr 2007
              • 117
              #4
              Re: CB80 Error Code

              As stated above, I have replaced the finisher board and the punch board, as well as the whole punch unit with a new board. Still getting this error.

              ANY OTHER ideas?

                Comment

                • scotjohn
                  Technician
                  • Dec 2008
                  • 15
                  #5
                  Re: CB80 Error Code

                  3.15.2 Registering the number of punch holes
                  This operation registers which puncher unit is attached to the IC on the punch driver PCB so that the
                  puncher unit can be identified by the finisher. For this reason, this operation must be performed when
                  the punch driver PCB has been replaced.
                  (1) Remove the rear cover of the finisher unit.
                  (2) Set bits 1 through 6 of DIPSW3 on the finisher controller PCB as indicated.
                  Fig. 3-97
                  (3) Set bits 7 and 8 on DIPSW3 on the finisher controller PCB to match the number of punch holes of
                  the attached puncher unit according to the table.
                  (4) Press SW1 on the finisher controller PCB. Press SW2 when setting a 2-/3-hole model (MJ-
                  6003N). Pressing this switch registers the number of punch holes to the punch driver PCB.
                  (5) Set all bits on DIPSW3 to OFF.
                  Number of Punch Holes
                  DIPSW3 bit settings
                  Push switch
                  bit 7 bit 8
                  2-hole OFF OFF SW1 (MJ-6003E) OFF OFF SW1
                  2-/3-hole OFF OFF SW2 (MJ-6003N) OFF OFF SW2
                  4-hole ON OFF SW1 (MJ-6003F) ON OFF SW1
                  4-hole ON ON SW1 (MJ-6003S) ON ON SW1

                    Comment

                    Previous template Next
                    Working...