Xerox Work Center 7556 ITB removal proceedure needed

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tonerjockey
    Senior Tech

    500+ Posts
    • Apr 2014
    • 567
    #1

    Xerox Work Center 7556 ITB removal proceedure needed

    Hello, i have a customer that heard a crinkling noise. i found a label stuck to the inside machine above the transfer belt. i removed the fuser, the drums, the drum door release lever, the belt cleaner unit as well as the waste container. i suspect that the drive coupler needs to be retracted, maybe in service mode. but i cheched there and didnt see anything pertaining to that.
    does anyone know what i need to do, or just run??

    thank you very much for any help. have a great weekend, Jim
    Tags: None
    • CanonSco
      Man About Town

      250+ Posts
      • Jul 2010
      • 368
      #2
      Re: Xerox Work Center 7556 ITB removal proceedure needed

      Almost.
      Lower lhs door flat.
      2 spring loaded brackets one either side / just under the fuser removed.
      Grey release plunger pulled out at rear underside of fuser.


      That's it. Pull itb out.
      Yes, I am a nerd.
      Gaming PC - check. Raspberry Pi - Check. Custom ROM on phone - check. Thick glasses - check.

        Comment

        • tonerjockey
          Senior Tech

          500+ Posts
          • Apr 2014
          • 567
          #3
          Re: Xerox Work Center 7556 ITB removal proceedure needed

          oh, cool. so, to recap. to lower the left side door flat, should i disconnect the rear door support limiter bracket? and the rear plunger, is that accessed from the back of the machine, but is about where the under side of the fuser is??

            Comment

            • rockdude
              Trusted Tech

              Site Contributor
              250+ Posts
              • Feb 2011
              • 257
              #4

                Comment

                • tonerjockey
                  Senior Tech

                  500+ Posts
                  • Apr 2014
                  • 567
                  #5
                  Re: Xerox Work Center 7556 ITB removal proceedure needed

                  thank you Rockdude and CanonSco.
                  so, line item # ( "9. Pull the Stopper Lever Latch. ), is that the "gray release plunger, at rear underside fuser" ?

                  i have to drive 15 miles into downtown to get there, so i want to be prepared.
                  sorry for the trouble. thank you very much guys. have a very nice day, JIm

                    Comment

                    • rockdude
                      Trusted Tech

                      Site Contributor
                      250+ Posts
                      • Feb 2011
                      • 257
                      #6
                      Re: Xerox Work Center 7556 ITB removal proceedure needed

                      Yes, That is the correct lever.

                      Be careful with two spring loaded lock brackets.

                      They ONLY go in a certain (correct) way.

                      Also when reinstalling the IBT assembly make sure you line it up correctly, DON'T FORCE IT!

                      Good luck.

                        Comment

                        • tonerjockey
                          Senior Tech

                          500+ Posts
                          • Apr 2014
                          • 567
                          #7
                          Re: Xerox Work Center 7556 ITB removal proceedure needed

                          ok cool. thank you very much.

                            Comment

                            • shinchan
                              Trusted Tech

                              100+ Posts
                              • May 2011
                              • 195
                              #8
                              Re: Xerox Work Center 7556 ITB removal proceedure needed

                              ibt removal from sm c3370/4470. I believe this is the same model as us model WC 7556
                              ibt removal.pdf

                                Comment

                                • tonerjockey
                                  Senior Tech

                                  500+ Posts
                                  • Apr 2014
                                  • 567
                                  #9
                                  Re: Xerox Work Center 7556 ITB removal proceedure needed

                                  Thank you very much Shinchan for the document. it will be very helpful. i do really appreciate your assistance.
                                  have a very nice day, Jim

                                    Comment

                                    Previous template Next
                                    Working...