My fiery x12 is broken

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • neonox
    • Jun 2025

    #1

    My fiery x12 is broken

    HELLO, I HAVE A PROBLEM, MY FIERY X12 IS BROKEN, AND I WANT TO INSTALL THE SOFTWARE ON ANOTHER PC CONTROL BOARD, IS THIS POSSIBLE?
    I HAVE A PENTIUM 4 OLD and can take advantage.
    SORRY FOR MY ENGLISH, BUT I NEED HELP, I CAN NOT WORK.
  • bojans
    Service Manager

    Site Contributor
    1,000+ Posts
    • Feb 2008
    • 1313

    #2
    How do you mean "broken"? Is it dead or doesn't boot?

    Comment

    • neonox

      #3
      CPU fan is broken and burned pentium, I tested the cpu in another motherboard old and does not work

      Comment

      • bojans
        Service Manager

        Site Contributor
        1,000+ Posts
        • Feb 2008
        • 1313

        #4
        If only cpu was burned you could change it.

        Comment

        • neonox

          #5
          that is not possible, I have another cpu but I do not accept the basis of fiery PLCA x12, the cpu I have is a Pentium 3 500 Mhz and the fiery x12 has a different or at least I think they do not know

          Comment

          • bojans
            Service Manager

            Site Contributor
            1,000+ Posts
            • Feb 2008
            • 1313

            #6
            I don't know which CPU is in your fiery, but you should bring it with you and visit local second hand shop. I believe people who works with computers can help you and find the same processor.

            Comment

            • bojans
              Service Manager

              Site Contributor
              1,000+ Posts
              • Feb 2008
              • 1313

              #7
              Originally posted by neonox
              that is not possible, I have another cpu but I do not accept the basis of fiery PLCA x12, the cpu I have is a Pentium 3 500 Mhz and the fiery x12 has a different or at least I think they do not know
              FIERY EX12 RIP SPECIFICATIONS says it's 866 MHz Intel CPU, so i believe 3500 Mhz is too much for that motherboard.

              Comment

              • neonox

                #8
                sorry for my writing is not 3500, is Pentium III 500 but does not start the system.

                Comment

                • bojans
                  Service Manager

                  Site Contributor
                  1,000+ Posts
                  • Feb 2008
                  • 1313

                  #9
                  I'm not sure that is proper cpu.
                  Are you sure that your motherboard is working too?

                  Comment

                  • neonox

                    #10
                    I'm from Spain and it is quite difficult to find a processor of this model, no more next is a Pentium III 700 or more, but I have not bought anything since I do not accept the pentium 500, the motherboard does not operate normally to be if you find a CPU .... it is possible to Secure the software on another pc? I have an old PC with Pentium IV 1.4 Ghz and 256 RAM and 20 GB hard drive, is available for installing the fiery? or I have to find a Pentium III that is valid for the original fiery?

                    Comment

                    • bojans
                      Service Manager

                      Site Contributor
                      1,000+ Posts
                      • Feb 2008
                      • 1313

                      #11
                      I never tried to make fiery on my own. That motherboard has special BIOS, so if you put those two boards from your fiery in your old PC it won't work.

                      Comment

                      • neonox

                        #12
                        if the specifications say it supports up to 866 CPU that supports a CPU wait 700, because I have no other solution, just buy another, because I can not put another pc. or there may be another solution??

                        Comment

                        • bojans
                          Service Manager

                          Site Contributor
                          1,000+ Posts
                          • Feb 2008
                          • 1313

                          #13
                          If your CPU and motherboard are dead best solution is to go on ebay and search for new fiery.
                          That's just my opinion. Maybe some other members can help you and point you on the right direction.

                          BR

                          Comment

                          • JimmyB
                            Technician

                            50+ Posts
                            • Jun 2008
                            • 77

                            #14
                            Fiery X12 only support CPU Celeron 300-533 Mhz s.370. You cant use Pentium III, only Celeron with FSB 100Mhz.
                            good luck

                            Comment

                            • jayc67
                              Independent technician
                              100+ Posts
                              • Sep 2009
                              • 100

                              #15
                              I send you a PM neonox, did you call Rex?

                              Comment

                              Working...