PDA

View Full Version : 4752 lifestop


Custom Search


BR549
11-14-2022, 09:24 PM
Does anyone know how to disable life stop for the IU on the 4752? Thanks.

Synthohol
11-14-2022, 09:47 PM
2.6 Life Stop Setting
2.6.1 Life stop
(1) Use
• To select whether or not to stop a print cycle when the maintenance kit reach its service life.
NOTE
▪ The settings of software Dip switch No.227 (bit7) and switch No. 230 (bit3) have priority.
(2) Default setting
• Off
(3) Setting item
• Enable
• Off

if it has already reached life the message may not go away, this is normally set prior to install.

tsbservice
11-14-2022, 10:59 PM
2.6 Life Stop Setting
2.6.1 Life stop
(1) Use
To select whether or not to stop a print cycle when the maintenance kit reach its service life.
NOTE
▪ The settings of software Dip switch No.227 (bit7) and switch No. 230 (bit3) have priority.
(2) Default setting
Off
(3) Setting item
Enable
Off

if it has already reached life the message may not go away, this is normally set prior to install.

Synthohol kindly this is for maintenance kit parts and OP asked about IU(drum-dev combo). Which is also in manual simply can't remember function/code.

Synthohol
11-15-2022, 04:06 AM
life stop is for drum and DV.
it can be overridden by those 2 dip sw.
also i wasnt aware of any konica maintenance kit for a office model. just for production machines.

tsbservice
11-15-2022, 07:37 AM
Those are all setting regarding IU life warnings/stop for this model.
As per Maintenance kit they are inherited from their Lexmark origin(see below).
"Maintenance kit" shown in the Service Mode is the generic name of the following maintenance parts.
However, parts are not supplied as a maintenance kit from the market, so place an order individually for each part.
Parts
Fuser
ACM pick roller
Transfer roller
Separator roller assembly
MPF pick roller and separator pad

Warning display Near Life Display Settings
(1) Use
To set whether or not to display the life warning of individual consumables.
When [Do Not Display] is selected, a warning is not displayed at the time of life detection.
However, in CS Remote Care, life warning is always sent to the Center regardless of this setting.
Applicable consumables are as follows:
Imaging unit, Maintenance kit
NOTE
▪ The settings of software Dip switch No.227 (bit7) and switch No. 230 (bit3) have priority.
(2) Default setting
Imaging unit: Display
Maintenance kit: Do Not Display
(3) Setting item
Display
Do Not Display
13.5 Software



Consumable Life Reminder
13.3.1 Use
To select whether or not to give the display of PM parts lifetime
PM parts lifetime display An entire screen warning is given when the service life of a specific unit has been reached,
prompting the user to replace the part.
Applicable units:
Imaging unit
Use to select not to give the display of PM parts lifetime.
Yes When the service life has been reached, a malfunction code and an entire screen warning appear on the control
panel.
No When the service life has been reached, a malfunction code and a message appear in one line on the upper side
of the screen.
13.3.2 Default setting
No
13.3.3 Setting item
Yes
No

SW No.051 HEX 00 - HEX80
1. Function
Settings for the life warning/replace display of the units
2. Setting value
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Normal display 00000000 / 00
00100000 20 Does not show the life warning/replace display
of the Imaging unit.
Reference
[Service Mode] -> [Counter] -> [Life]

Custom Search