Strange Issue on a Biz 210

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • groovy
    Trusted Tech
    100+ Posts
    • Apr 2009
    • 179
    #1

    Strange Issue on a Biz 210

    Hi all,
    today i noticed a strange issue into an imaging unit of a bizhub 210.
    The toner recycling section, under the wiper blade, is making a strange noise.
    I serviced lots of this imaging unit (same of the older konica's 7115) but i never noticed this.
    Someone here can post a pic close to the recycling section on this imaging unit?

    I've replaced the wiper blade, the developer and the drum, but this noise (like bad mylars under the recovery/wiper blade) is new...
    Tags: bad, bizhub, developer, drum, issue, konica, noise, recovery, toner, unit
    • minimerlin
      Senior Tech
      Site Contributor
      500+ Posts
      • Nov 2007
      • 851
      #2
      Re: Strange Issue on a Biz 210

      Is it a squeek? Normally it is caused by the plastic bushes at each end of the shafts in the recycling area. Give them a good clean and a very tiny wipe of lube.
      Please do not PM me without asking first.

        Comment

        • groovy
          Trusted Tech
          100+ Posts
          • Apr 2009
          • 179
          #3
          Re: Strange Issue on a Biz 210

          Thank you for the reply.
          It's not really a squeak, it's more a rubbing noise.
          (it is difficult for me explain in a foreing language...)
          Luigi - Digitalix Srl

            Comment

            • pepper38_cnd
              Field Service Manager
              Site Contributor
              1,000+ Posts
              • Aug 2005
              • 1076
              #4
              Re: Strange Issue on a Biz 210

              Was your original call for Black smuges or streaks? You found the recycle section packed? If so the plastic shaft in the recycle section may have broken and be causing your noise. Remove the drum, with the spout on your right, turn the white gear on the left by hand the small black gears at the base of the toner spout should be turning if they are not then the shaft has broken.
              Online Store is closed. Chip resetting is a thing of the past! Thank you to all my past customers.
              Now into Ip TV KODI Boxes

                Comment

                • boanda
                  Technician
                  • Feb 2011
                  • 79
                  #5
                  Re: Strange Issue on a Biz 210

                  I have had similary problem, nothing was broken, I replaced three black gears on the right side of developing unit and that works fine for about 15k copies,and starts again,and again,until I replaced whole UI. This problem I had only with BH162/ineo161

                    Comment

                    • groovy
                      Trusted Tech
                      100+ Posts
                      • Apr 2009
                      • 179
                      #6
                      Re: Strange Issue on a Biz 210

                      So the imaging unit has definively dead.
                      Can be replaced with the unit from a konica 7115?

                        Comment

                        • mrwho
                          Major Asshole!
                          Site Contributor
                          2,500+ Posts
                          • Apr 2009
                          • 4297
                          #7
                          Re: Strange Issue on a Biz 210

                          Usually when the wheels start getting loose (packing the toner in the cleaner blade) I put a couple of drops of superglue to fix the wheels onto their shafts. Usually lasts longer than just replacing them.
                          ' "But the salesman said . . ." The salesman's an asshole!'
                          Mascan42

                          'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'
                          Ibid

                          I'm just an ex-tech lurking around and spreading disinformation!

                            Comment

                            • groovy
                              Trusted Tech
                              100+ Posts
                              • Apr 2009
                              • 179
                              #8
                              Re: Strange Issue on a Biz 210

                              OK, today i've just replaced the IU with onther one, used but in good condition.
                              For my things, i've removed the entire front panel and i've noticed a very big spill of toner lying on the bottom of the copier.
                              Performed a hard cleaning and i hope no other spill exists.
                              Can the toner supply system be broken?

                                Comment

                                Previous template Next
                                Working...